- 您现在的位置：买卖IC网 > PDF目录373702 > TS3405 (Taiwan Semiconductor Co., Ltd.) Single Synchronous Buck PWM Controller PDF资料下载
参数资料
| 型号： | TS3405 |
| 厂商： | Taiwan Semiconductor Co., Ltd. |
| 英文描述： | Single Synchronous Buck PWM Controller |
| 中文描述： | 单同步降压PWM控制器 |
| 文件页数： | 9/10页 |
| 文件大小： | 409K |
| 代理商： | TS3405 |
Application Guidelines (continued)
The equations below relate the compensation network’s
poles, zeros and gain to the components (R
1
, R
2
, R
3
, C
1
,
C
2
and C
3
) in Fig. 7. Use these guidelines for locating the
poles and zeros of the compensation network:
1. Pick Gain (R
2
/R
1
) for desired converter bandwidth.
2. Place 1
st
zero below filter’s double pole (~75% F
LC
)
3. Place 2
nd
zero at filter’s double pole.
4. Place 1
st
pole at the ESR zero.
5. Place 2
nd
pole at half the switching frequency
6. Check gain against error amplifier’s open-loop gain.
7. Estimate phase margin – repeat if necessary.
Output Capacitor Selection
An output capacitor is required to filter the output and
supply
the
load
transient
requirements are a function of the switching frequency
and the ripple current. The load transient requirements
are a function of the slew rate (di/dt) and the magnitude
of the transient load current. These requirements are
generally met with a mix of capacitors and careful layout.
Modern components and loads are capable of producing
transient load rates above 1A/nS. High frequency
capacitors initially supply the transient and slow the
current load rate seen by the bulk capacitors. The bulk
filter capacitor values are generally determined by the
ESR (Effective Series Resistance) and voltage rating
requirements
rather
than
requirements.
High frequency decoupling capacitors should be placed
as close to the power pins of the load as physically
possible. Be careful not to add inductance in the circuit
board wiring that could cancel the usefulness of these
low
inductance
components.
manufacturer of the load on specific decoupling
requirements.
Use only specialized low-ESR capacitors intended for
switching-regulator applications for the bulk capacitors.
The bulk capacitor’s ESR will determine the output ripple
voltage and the initial voltage drop after a high slew-rate
transient. An aluminum electrolytic capacitor’s ESR value
is related to the case size with lower ESR available in
larger case sizes. However, the equivalent Series
inductance (ESL) of these capacitors increases with case
size and can reduce the usefulness of the capacitor to
high slew-rate transient loading. Unfortunately, ESL is
not a specified parameter. Work with your capacitor
supplier and measure the capacitor’s impedance with
frequency to select a suitable component.
current. The filtering
actual
capacitance
Consult
with
the
In most cases, multiple electrolytic capacitors of small
case size perform better than a single large case
capacitor.
Feedback Divider
The reference of TS3405 is 0.8V. the output voltage can
be set by R
1
and R
4
as shown in Fig. 4. The equation is
following:
Vout = 0.8 x (1 + R
1
/ R
4
)
The R1 should be between 2k
to 5k
. put the R
1
, R
4
and others compensation component as close to TS3405
as possible.
Shutdown
Pulling low the COMP pin can shutdown the TS3405
PWM controller. You can use a small single transistor as
switch like as JP1 shown in Fig. 4.
Compensation Break Frequency Equations
As in any high frequency switching converter, layout is
very important. Switching current from one power device
to another can generate voltage transients across the
impedances of the interconnecting bond wires and circuit
traces. Using wide, short printed circuit traces should
minimize these interconnecting impedances. The critical
components should be located as close together as
possible, using ground plane construction or single point
grounding.
To minimize the voltage overshoot, the interconnecting
wires indicated by heavy lines should be part of a ground
or power plane in a printed circuit board. Locate the
TS3405 within 3 inches of the MOSFETs. Q1 and Q2.
The circuit traces for the MOSFETs’ gate and source
connections from the TS3405 must be sized to handle up
to 1A peak current. Provide local Vcc decoupling
between Vcc and Gnd pins. Locate the capacitor, C
BOOT
as close as practical to the Boot and Phase pins. All
components used for feedback compensation should be
located as close to the IC a practical.
TS3405
9-10
2003/12 rev. A
相关PDF资料 |
PDF描述 |
|---|---|
| TS3405CS | Single Synchronous Buck PWM Controller |
| TS34063A | Dc to Dc Converter Controller |
| TS34063ACD | Dc to Dc Converter Controller |
| TS34063ACS | Dc to Dc Converter Controller |
| TS34063 | Dc to Dc Converter Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS3405CS | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Single Synchronous Buck PWM Controller |
| TS3406 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:600mA / 1.5MHz Synchronous Buck Converter |
| TS3406_08 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:600mA / 1.5MHz Synchronous Buck Converter |
| TS3406_13 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:600mA / 1.5MHz Synchronous Buck Converter |
| TS34063 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Dc to Dc Converter Controller |
发布紧急采购，3分钟左右您将得到回复。