- 您现在的位置：买卖IC网 > PDF目录365960 > TS80C31X2-MCCD (TEMIC SEMICONDUCTORS) 8-bit CMOS Microcontroller ROMless PDF资料下载
参数资料
| 型号： | TS80C31X2-MCCD |
| 厂商： | TEMIC SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-bit CMOS Microcontroller ROMless |
| 中文描述： | 8-BIT, 40 MHz, MICROCONTROLLER, PQFP44 |
| 封装： | PLASTIC, QFP-44 |
| 文件页数： | 5/40页 |
| 文件大小： | 484K |
| 代理商： | TS80C31X2-MCCD |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
Rev. A - Mar. 19, 1999
5
Preliminary
TS80C31X2
Table 2. Pin Description for 40/44 pin packages
PIN NUMBER
TYPE
DIL
LCC
VQFP 1.4
Ground:
0V reference
1
39
I
Optional Ground:
Contact the Sales Office for ground connection.
Power Supply:
This is the power supply voltage for normal, idle and power-
down operation
39-32
43-36
37-30
I/O
Port 0
: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s
written to them float and can be used as high impedance inputs. Port 0 is also
the multiplexed low-order address and data bus during access to external program
and data memory. In this application, it uses strong internal pull-up when emitting
1s.
1-8
2-9
40-44
1-3
pins that have 1s written to them are pulled high by the internal pull-ups and
can be used as inputs. As inputs, Port 1 pins that are externally pulled low will
source current because of the internal pull-ups.
21-28
24-31
18-25
I/O
Port 2
: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2
pins that have 1s written to them are pulled high by the internal pull-ups and
can be used as inputs. As inputs, Port 2 pins that are externally pulled low will
source current because of the internal pull-ups. Port 2 emits the high-order address
byte during fetches from external program memory and during accesses to external
data memory that use 16-bit addresses (MOVX @DPTR).In this application, it
uses strong internal pull-ups emitting 1s. During accesses to external data memory
that use 8-bit addresses (MOVX @Ri), port 2 emits the contents of the P2 SFR.
10-17
11,
13-19
7-13
pins that have 1s written to them are pulled high by the internal pull-ups and
can be used as inputs. As inputs, Port 3 pins that are externally pulled low will
source current because of the internal pull-ups. Port 3 also serves the special
features of the 80C51 family, as listed below.
10
11
5
I
RXD (P3.0):
Serial input port
11
13
7
O
TXD (P3.1):
Serial output port
12
14
8
I
INT0 (P3.2):
External interrupt 0
13
15
9
I
INT1 (P3.3):
External interrupt 1
14
16
10
I
T0 (P3.4):
Timer 0 external input
15
17
11
I
T1 (P3.5):
Timer 1 external input
16
18
12
O
WR (P3.6):
External data memory write strobe
17
19
13
O
RD (P3.7):
External data memory read strobe
9
10
4
I
Reset:
A high on this pin for two machine cycles while the oscillator is running,
resets the device. An internal diffused resistor to V
SS
permits a power-on reset
using only an external capacitor to V
CC.
30
33
27
O (I)
Address Latch Enable:
Output pulse for latching the low byte of the address
during an access to external memory. In normal operation, ALE is emitted at a
constant rate of 1/6 (1/3 in X2 mode) the oscillator frequency, and can be used
for external timing or clocking. Note that one ALE pulse is skipped during each
access to external data memory.
29
32
26
O
Program Store ENable:
The read strobe to external program memory. When
executing code from the external program memory, PSEN is activated twice each
machine cycle, except that two PSEN activations are skipped during each access
to external data memory. PSEN is not activated during fetches from internal
program memory.
31
35
29
I
External Access Enable:
EA must be externally held low to enable the device
to fetch code from external program memory locations.
19
21
15
I
Crystal 1:
Input to the inverting oscillator amplifier and input to the internal
clock generator circuits.
18
20
14
O
Crystal 2:
Output from the inverting oscillator amplifier
MNEMONIC
NAME AND FUNCTION
V
SS
Vss1
20
22
16
I
V
CC
40
44
38
I
P0.0-P0.7
P1.0-P1.7
I/O
Port 1:
Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1
P2.0-P2.7
P3.0-P3.7
5,
I/O
Port 3:
Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3
Reset
ALE
PSEN
EA
XTAL1
XTAL2
相关PDF资料 |
PDF描述 |
|---|---|
| TS80C31X2-MCCR | Alligator Clip Color:Red |
| TS80C31X2-MCEB | 8-bit CMOS Microcontroller ROMless |
| TS80C31X2-MCA | 8-bit CMOS Microcontroller ROMless(601.14 k) |
| TS80C31X2-MCB | 8-bit CMOS Microcontroller ROMless(601.14 k) |
| TS81102G0FS | TS81102G0FS Summary [Updated 9/03. 10 Pages] DMUX 8/10 bit. 2 Gsps. 1:4/1:8. for military applications |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS80C31X2-MCCR | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:8-bit CMOS Microcontroller 0-60 MHz |
| TS80C31X2-MCE | 功能描述:IC MCU 8BIT 40/20MHZ 44-VQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:80C 标准包装:1,500 系列:AVR® ATtiny 核心处理器:AVR 芯体尺寸:8-位 速度:16MHz 连通性:I²C，LIN，SPI，UART/USART，USI 外围设备:欠压检测/复位，POR，PWM，温度传感器，WDT 输入/输出数:16 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:带卷 (TR) |
| TS80C31X2-MCEB | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:8-bit CMOS Microcontroller 0-60 MHz |
| TS80C31X2-MCED | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit CMOS Microcontroller ROMless |
| TS80C31X2-MCER | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit CMOS Microcontroller ROMless |
发布紧急采购，3分钟左右您将得到回复。