参数资料
| 型号： | TS80C31X2-VIE |
| 厂商： | Atmel |
| 文件页数： | 7/42页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8BIT 40/30MHZ 44-VQFP |
| 标准包装： | 160 |
| 系列： | 80C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 60/30MHz |
| 连通性： | UART/USART |
| 外围设备： | POR |
| 输入/输出数： | 32 |
| 程序存储器类型： | ROMless |
| RAM 容量： | 128 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-QFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
15
4428E–8051–02/08
AT/TS80C31X2
Reset Value = 0000 0000b
Bit addressable
Table 9-3.
SCON Register -- SCON - Serial Control Register (98h)
7
6
5
4
3
2
1
0
FE/SM0
SM1
SM2
REN
TB8
RB8
TI
RI
Bit
Number
Bit
Mnemonic
Description
7
FE
Framing Error bit (SMOD0=1)
Clear to reset the error state, not cleared by a valid stop bit.
Set by hardware when an invalid stop bit is detected.
SMOD0 must be set to enable access to the FE bit
SM0
Serial port Mode bit 0
Refer to SM1 for serial port mode selection.
SMOD0 must be cleared to enable access to the SM0 bit
6
SM1
Serial port Mode bit 1
SM0
SM1 Mode Description
Baud Rate
0
Shift Register F
XTAL/12 (/6 in X2 mode)
0
1
8-bit UART
Variable
1
0
2
9-bit UART
F
XTAL/64 or FXTAL/32 (/32, /16 in X2 mode)
1
3
9-bit UART
Variable
5
SM2
Serial port Mode 2 bit / Multiprocessor Communication Enable bit
Clear to disable multiprocessor communication feature.
Set to enable multiprocessor communication feature in mode 2 and 3, and eventually mode 1. This bit should be
cleared in mode 0.
4
REN
Reception Enable bit
Clear to disable serial reception.
Set to enable serial reception.
3
TB8
Transmitter Bit 8 / Ninth bit to transmit in modes 2 and 3.
Clear to transmit a logic 0 in the 9th bit.
Set to transmit a logic 1 in the 9th bit.
2
RB8
Receiver Bit 8 / Ninth bit received in modes 2 and 3
Cleared by hardware if 9th bit received is a logic 0.
Set by hardware if 9th bit received is a logic 1.
In mode 1, if SM2 = 0, RB8 is the received stop bit. In mode 0 RB8 is not used.
1
TI
Transmit Interrupt flag
Clear to acknowledge interrupt.
Set by hardware at the end of the 8th bit time in mode 0 or at the beginning of the stop bit in the other modes.
0
RI
Receive Interrupt flag
Clear to acknowledge interrupt.
Set by hardware at the end of the 8th bit time in mode 0, see Figure 9-2. and Figure 9-3. in the other modes.
相关PDF资料 |
PDF描述 |
|---|---|
| TS87C51RC2-MCE | IC MCU 8BIT 32K OTP 40MHZ 44VQFP |
| TS87C51RC2-LIE | IC MCU 8BIT 32K OTP 40MHZ 44VQFP |
| TS87C51RD2-MCE | IC MCU 8BIT 64K OTP 40MHZ 44VQFP |
| TS80C51RD2-VIE | IC MCU 8BIT 768BYTE 40MHZ 44VQFP |
| TS87C51RC2-MIE | IC MCU 8BIT 32K OTP 40MHZ 44VQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS80C31X2-VIEB | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:8-bit CMOS Microcontroller 0-60 MHz |
| TS80C31X2-VIED | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:8-bit CMOS Microcontroller 0-60 MHz |
| TS80C31X2-VIER | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:8-bit CMOS Microcontroller 0-60 MHz |
| TS80C31X2-VLAB | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit CMOS Microcontroller ROMless |
| TS80C31X2-VLAD | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit CMOS Microcontroller ROMless |
发布紧急采购，3分钟左右您将得到回复。