- 您现在的位置：买卖IC网 > PDF目录225343 > TS80C32X2-VIA (ATMEL CORP) 8-BIT, 60 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | TS80C32X2-VIA |
| 厂商： | ATMEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, 60 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | PLASTIC, DIP-40 |
| 文件页数： | 19/55页 |
| 文件大小： | 596K |
| 代理商： | TS80C32X2-VIA |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
26
TS8xCx2X2
4184I–8051–02/08
Idle mode
An instruction that sets PCON.0 causes that to be the last instruction executed before
going into the Idle mode. In the Idle mode, the internal clock signal is gated off to the
CPU, but not to the interrupt, Timer, and Serial Port functions. The CPU status is pre-
served in its entirely : the Stack Pointer, Program Counter, Program Status Word,
Accumulator and all other registers maintain their data during Idle. The port pins hold
the logical states they had at the time Idle was activated. ALE and PSEN hold at logic
high levels.
There are two ways to terminate the Idle. Activation of any enabled interrupt will cause
PCON.0 to be cleared by hardware, terminating the Idle mode. The interrupt will be ser-
viced, and following RETI the next instruction to be executed will be the one following
the instruction that put the device into idle.
The flag bits GF0 and GF1 can be used to give an indication if an interrupt occured dur-
ing normal operation or during an Idle. For example, an instruction that activates Idle
can also set one or both flag bits. When Idle is terminated by an interrupt, the interrupt
service routine can examine the flag bits.
The other way of terminating the Idle mode is with a hardware reset. Since the clock
oscillator is still running, the hardware reset needs to be held active for only two
machine cycles (24 oscillator periods) to complete the reset.
Power-down Mode
To save maximum power, a power-down mode can be invoked by software (Refer to
Table 10., PCON register).
In power-down mode, the oscillator is stopped and the instruction that invoked power-
down mode is the last instruction executed. The internal RAM and SFRs retain their
value until the power-down mode is terminated. VCC can be lowered to save further
power. Either a hardware reset or an external interrupt can cause an exit from power-
down. To properly terminate power-down, the reset or external interrupt should not be
executed before VCC is restored to its normal operating level and must be held active
long enough for the oscillator to restart and stabilize.
Only external interrupts INT0 and INT1 are useful to exit from power-down. For that,
interrupt must be enabled and configured as level or edge sensitive interrupt input.
Holding the pin low restarts the oscillator but bringing the pin high completes the exit as
detailed in Figure 10. When both interrupts are enabled, the oscillator restarts as soon
as one of the two inputs is held low and power down exit will be completed when the first
input will be released. In this case the higher priority interrupt service routine is exe-
cuted.
Once the interrupt is serviced, the next instruction to be executed after RETI will be the
one following the instruction that put TS80C52X2 into power-down mode.
Figure 10. Power-down Exit Waveform
INT1
INT0
XTAL1
Power-down phase
Oscillator restart phase
Active phase
相关PDF资料 |
PDF描述 |
|---|---|
| TS80C32X2-LIA | 8-BIT, 30 MHz, MICROCONTROLLER, PDIP40 |
| TS87C51RB2-EBR | 8-BIT, OTPROM, MICROCONTROLLER, PQCC44 |
| TS80C51RD2-MCBB | 8-BIT, 40 MHz, MICROCONTROLLER, PQCC44 |
| TS83C51RB2ZZZ-VCBB | 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PQCC44 |
| TS80C51RD2-MCLB | 8-BIT, 40 MHz, MICROCONTROLLER, PQCC68 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS80C32X2-VIAB | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:8-bit CMOS Microcontroller 0-60 MHz |
| TS80C32X2-VIAD | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:8-bit CMOS Microcontroller 0-60 MHz |
| TS80C32X2-VIAR | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:8-bit CMOS Microcontroller 0-60 MHz |
| TS80C32X2-VIB | 功能描述:IC MCU 8BIT 40/20MHZ 44-PLCC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:80C 标准包装:1,500 系列:AVR® ATtiny 核心处理器:AVR 芯体尺寸:8-位 速度:16MHz 连通性:I²C，LIN，SPI，UART/USART，USI 外围设备:欠压检测/复位，POR，PWM，温度传感器，WDT 输入/输出数:16 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:带卷 (TR) |
| TS80C32X2-VIBB | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:8-bit CMOS Microcontroller 0-60 MHz |
发布紧急采购，3分钟左右您将得到回复。