参数资料
| 型号： | TS87C51RC2-MIE |
| 厂商： | Atmel |
| 文件页数： | 9/84页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8BIT 32K OTP 40MHZ 44VQFP |
| 标准包装： | 160 |
| 系列： | 87C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 40/20MHz |
| 连通性： | UART/USART |
| 外围设备： | POR，PWM，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 32KB（32K x 8） |
| 程序存储器类型： | OTP |
| RAM 容量： | 512 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-QFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
2007-2012 Microchip Technology Inc.
DS70292G-page 19
dsPIC33FJ32GP302/304, dsPIC33FJ64GPX02/X04, AND dsPIC33FJ128GPX02/X04
2.0
GUIDELINES FOR GETTING
STARTED WITH 16-BIT
DIGITAL SIGNAL
CONTROLLERS
2.1
Basic Connection Requirements
Getting started with the dsPIC33FJ32GP302/304,
dsPIC33FJ64GPX02/X04, and dsPIC33FJ128GPX02/
X04 family of 16-bit Digital Signal Controllers (DSCs)
requires attention to a minimal set of device pin
connections before proceeding with development. The
following is a list of pin names, which must always be
connected:
All VDD and VSS pins
All AVDD and AVSS pins (regardless if ADC module
is not used)
VCAP
MCLR pin
PGECx/PGEDx pins used for In-Circuit Serial
Programming (ICSP) and debugging purposes
(see Section 2.5 “ICSP Pins”)
OSC1 and OSC2 pins when external oscillator
source is used
Additionally, the following pins may be required:
VREF+/VREF- pins used when external voltage
reference for ADC module is implemented
2.2
Decoupling Capacitors
The use of decoupling capacitors on every pair of
power supply pins, such as VDD, VSS, AVDD and
AVSS is required.
Consider the following criteria when using decoupling
capacitors:
Value and type of capacitor: Recommendation
of 0.1 F (100 nF), 10-20V. This capacitor should
be a low-ESR and have resonance frequency in
the range of 20 MHz and higher. It is
recommended that ceramic capacitors be used.
Placement on the printed circuit board: The
decoupling capacitors should be placed as close
to the pins as possible. It is recommended to
place the capacitors on the same side of the
board as the device. If space is constricted, the
capacitor can be placed on another layer on the
PCB using a via; however, ensure that the trace
length from the pin to the capacitor is within
one-quarter inch (6 mm) in length.
Handling high frequency noise: If the board is
experiencing high frequency noise, upward of
tens of MHz, add a second ceramic-type capacitor
in parallel to the above described decoupling
capacitor. The value of the second capacitor can
be in the range of 0.01 F to 0.001 F. Place this
second capacitor next to the primary decoupling
capacitor. In high-speed circuit designs, consider
implementing a decade pair of capacitances as
close to the power and ground pins as possible.
For example, 0.1 F in parallel with 0.001 F.
Maximizing performance: On the board layout
from the power supply circuit, run the power and
return traces to the decoupling capacitors first,
and then to the device pins. This ensures that the
decoupling capacitors are first in the power chain.
Equally important is to keep the trace length
between the capacitor and the power pins to a
minimum thereby reducing PCB track inductance.
Note 1: This data sheet summarizes the features
of
the
dsPIC33FJ32GP302/304,
dsPIC33FJ64GPX02/X04,
and
dsPIC33FJ128GPX02/X04
family
of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to the “dsPIC33F/PIC24H
Family Reference Manual”, which is
available from the Microchip website
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be avail-
able on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
Note:
The AVDD and AVSS pins must be
connected independent of the ADC
voltage reference source.
相关PDF资料 |
PDF描述 |
|---|---|
| TS87C51RB2-LCE | IC MCU 8BIT 16K OTP 30MHZ 44VQFP |
| TS87C51RD2-LIE | IC MCU 8BIT 64K OTP 30MHZ 44VQFP |
| TS87C51RB2-LIE | IC MCU 8BIT 16K OTP 30MHZ 44VQFP |
| TS87C51RC2-LCE | IC MCU 8BIT 32K OTP 40MHZ 44VQFP |
| 52271-2469 | CONN FFC 24POS 1MM R/A SMD ZIF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS87C51RC2-MIEB | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| TS87C51RC2-MIED | 制造商:Atmel Corporation 功能描述:MCU 8-Bit AT87 80C51 CISC 32KB EPROM 5V 44-Pin VQFP |
| TS87C51RC2-MIER | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| TS87C51RC2-VCA | 功能描述:IC MCU 8BIT 32K OTP 40MHZ 40-DIP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:87C 标准包装:1,500 系列:AVR® ATtiny 核心处理器:AVR 芯体尺寸:8-位 速度:16MHz 连通性:I²C，LIN，SPI，UART/USART，USI 外围设备:欠压检测/复位，POR，PWM，温度传感器，WDT 输入/输出数:16 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:带卷 (TR) |
| TS87C51RC2-VCAD | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。