- 您现在的位置：买卖IC网 > PDF目录373736 > TSH310 (意法半导体) Fasteners, Spacers/standoffs; Spacing Height:1.5"; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No PDF资料下载
参数资料
| 型号： | TSH310 |
| 厂商： | 意法半导体 |
| 英文描述： | Fasteners, Spacers/standoffs; Spacing Height:1.5"; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No |
| 中文描述： | 四楼高速运算放大器 |
| 文件页数： | 10/19页 |
| 文件大小： | 449K |
| 代理商： | TSH310 |
TSH310
Power Supply Considerations
10/19
4 Power Supply Considerations
Correct power supply bypassing is very important for optimizing performance in high-frequency ranges.
Bypass capacitors should be placed as close as possible to the IC pins to improve high-frequency
bypassing. A capacitor greater than 1
μ
F is necessary to minimize the distortion. For better quality
bypassing, a capacitor of 10nF can be added using the same implementation conditions. Bypass
capacitors must be incorporated for both the negative and the positive supply.
For example: on the SO8_SINGLE_HF board, these capacitors are C6, C7, C8, C9.
Single power supply
In the event that a single supply system is used, new biasing is necessary to assume a positive output
dynamic range between 0V and +V
CC
supply rails. Considering the values of V
OH
and V
OL
, the amplifier
will provide an output dynamic from +0.9V to +4.1V on 1k
load.
The amplifier must be biased with a mid-supply (nominally +V
CC
/2), in order to maintain the DC
component of the signal at this value. Several options are possible to provide this bias supply, such as a
virtual ground using an operational amplifier or a two-resistance divider (which is the cheapest solution).
A high resistance value is required to limit the current consumption. On the other hand, the current must
be high enough to bias the non-inverting input of the amplifier. If we consider this bias current (55
μ
A
max.) as the 1% of the current through the resistance divider to keep a stable mid-supply, two resistances
of 470
can be used.
The input provides a high pass filter with a break frequency below 10Hz which is necessary to remove the
original 0 volt DC component of the input signal, and to fix it at +V
CC
/2.
Figure 27
illustrates a 5V single power supply configuration for the SO8_SINGLE evaluation board (see
Evaluation Boards
on page 9).
Figure 26: Circuit for power supply bypassing
+
-V
CC
+V
CC
10microF
+
10nF
+
10nF
-
10microF
相关PDF资料 |
PDF描述 |
|---|---|
| TSH310ID | 400A High-Speed Operational Amplifier |
| TSH310IDT | 400A High-Speed Operational Amplifier |
| TSH310ILT | 400A High-Speed Operational Amplifier |
| TSH330 | 1.1 GHz Low-Noise Operational Amplifier |
| TSH330I | 1.1 GHz Low-Noise Operational Amplifier |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TSH310ID | 功能描述:运算放大器 - 运放 Hi Spd Op Amp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| TSH310IDT | 功能描述:运算放大器 - 运放 Single Lo Pwr Hi-Spd RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| TSH310ILT | 功能描述:运算放大器 - 运放 Single Lo Pwr Hi-Spd RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| TSH31I | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:280MHz BANDWIDTH MOS INPUT SINGLE OPERATIONAL AMPLIFIER |
| TSH31ID | 功能描述:运算放大器 - 运放 Single MOS Input RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。