- 您现在的位置：买卖IC网 > PDF目录373745 > TSS461CR LAN Node Controller PDF资料下载
参数资料
| 型号： | TSS461CR |
| 英文描述： | LAN Node Controller |
| 中文描述： | 网络节点控制器 |
| 文件页数： | 25/52页 |
| 文件大小： | 268K |
| 代理商： | TSS461CR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
TSS461C
25
Rev. D (22 Feb 01)
ETIP
: Enable Transmission In Progress
One : Enable TIP generation
Zero : Disable TIP generation.
–
The Transmission In Progress (TIP), tells the diagnosis system to
enable transmission diagnosis.
ESDC
: Enable System Diagnosis Clock
One : Enable SDC divider.
Zero : Disable SDC divider.
–
The Synchronous Diagnosis Clock (SDC), controls the cycle time of
the synchronous diagnosis.
9.2.4. Command Register (0x03) :
7
6
5
4
3
2
1
0
GRES
SLEEP
IDLE
ACTI
REAR
0
0
MSDC
Write only register.
Reserved : Bit 1, 2 these bit must not be set by the user ; a zero must always be written to these bit.
If the circuit is operating at low birates there might be a considerable delay between the writing of this register and
the performing of the actual command (worst case 6 timeslots). The user is therefore recommanded to verify, by
reading the Line Status Register (0x04) that the commands have been performed.
GRES
: General Reset.
The Reset circuit command bit performs, if set, exactly as if the external
reset pin was asserted. This command bit has its own auto-reset circuitry.
One : Reset active
Zero : Reset inactive
SLEEP
: Sleep command.
If the user sets the Sleep bit, the circuit will enter sleep mode. When the
circuit is in sleep mode, all non-user registers are setup to minimize
power consumption and the oscillator is stopped. To exit from this mode
the user must set either the idle or activate commands.
One : Sleep active
Zero : Sleep inactive
IDLE
: Idle command.
If the user sets the Idle bit, the circuit will enter idle mode. In idle mode
the oscillator will operate, but the TSS461C will not transmit or receive
anything on the bus, and the TXD output will be in three state
One : Idle active
Zero : Idle inactive
ACTI
: Activate command.
The Activate command will put the circuit in the active mode, i.e it will
transmit and receive normally on the bus. When the circuit is in activate
mode the TXD three-state output is enabled.
One : Activate active
Zero : Activate inactive
REAR
: Re-Arbitrate command.
This command will, after the current attempt, reset the retry counter and
re-arbitrate the messages to be transmitted in order to find the highest
priority message to transmit.
One : Re-arbitrate active
Zero : Re-arbitrate inactive
MSDC
: Manual System Diagnosis Clock.
Rather than using the SDC divider described in section 9.2.3., the user
can use the manual SDC command to generate a SDC pulse for the
diagnosis system.
This MSDC pulse should be high at least two timeslot clock.
相关PDF资料 |
PDF描述 |
|---|---|
| TSS463-AA | TSS463-AA [Updated 3/03. 60 Pages] |
| TSS463D | Industrial Control IC |
| TSS463R | Industrial Control IC |
| TSS461E | VAN Data Link Controller |
| TSS461E-TDRA-9 | VAN Data Link Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TSS461C-TDRZ | 功能描述:网络控制器与处理器 IC ASICS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| TSS461CVAN | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:Van Controller Serial Interface |
| TSS461E | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:VAN Data Link Controller |
| TSS461E_06 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:VAN Data Link Controller |
| TSS461E-TDRA-9 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:VAN Data Link Controller |
发布紧急采购，3分钟左右您将得到回复。