参数资料
| 型号： | TSSOP20EV |
| 厂商： | Microchip Technology |
| 文件页数： | 12/30页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR MCP43X |
| 标准包装： | 1 |
| 主要目的： | 裸评估板 |
| 嵌入式： | 否 |
| 主要属性： | TSSOP-20/16/14/8 和 SSOP-20 评估板 |
| 次要属性： | 用于 PICmicro? MCU、ADC、DAC 和其它设备 |
| 已供物品： | 5 裸板，文档 |
| 产品目录页面： | 659 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Thermistor and RTD Solutions
Thermistor Solutions
Typically, thermistors require an external resistor for biasing.
In addition, the inherent non-linearity of a thermistor is
improved by biasing the thermistor in a resistive ladder
circuit to linearize the temperature-to-voltage conversion.
Typically, the thermistor voltage is directly connected to an
ADC to digitize the voltage measurement. The measured
voltage is converted to temperature using a lookup table.
However, at hot and cold temperature extremes the non-
linearity of this approach is much greater with reduced
change in voltage, which results in lower accuracy. This
requires higher resolution and a more costly ADC.
The solution is to use Microchip’s Linear Active Thermistors,
the MCP9700 and MCP9701 . These are low-cost voltage
output temperature sensors that replace almost any
Thermistor application solutions. Unlike resistive type
sensors such as Thermistors, the signal conditioning
and noise immunity circuit development overhead can be
avoided by using the low-cost Linear Active Thermistors.
RTD Solution
Resistive Temperature Detectors (RTDs) are highly accurate
and repeatable temperature sensing elements. When
using these sensors a robust instrumentation circuit is
required and it is typically used in high performance thermal
management applications such as medical instrumentation.
This solution uses a high performance Delta-Sigma Analog-
to-Digital converter, and two resistors to measure RTD
resistance ratiometrically. A ±0.1°C accuracy and ±0.01°C
measurement resolution can be achieved across the RTD
temperature range of -200°C to +800°C with a single point
calibration.
This solution uses a common reference voltage to bias
the RTD and the ADC which provides a ratio-metric relation
between the ADC resolution and the RTD temperature
resolution. Only one biasing resistor, RA, is needed to set the
measurement resolution ratio (shown in equation below).
RTD Resistance
These sensors output voltage is proportional to ambient
temperature with temperature coef?cient of 10 mV/°C and
19.5 mV/°C. Unlike thermistors, these devices do not require
RRTD = RA
( 2 n – Code – 1 Code )
additional computation for temperature measurement.
The factory set coef?cients provide linear interface to
measure ambient temperatures (refer to AN1001 for sensor
optimization).
MCP9700 and MCP9701 Key Features
■ ? SC70, TO92 packages
■ ? Operating temperature range: -40°C to +150°C
■ ? Temperature Coef?cient: 10 mV/°C ( MCP9700 )
■ ? Temperature Coef?cient: 19.5 mV/°C ( MCP9701 )
■ ? Low power: 6 μA (typ.)
Applications
■ Refrigeration equipment
■ Power supply over temperature protection
■ General purpose temperature monitoring
Where:
Code = ADC output code
RA = Biasing resistor
n = ADC number of bits
(22 bits with sign, MCP3551)
For instance, a 2V ADC reference voltage (V REF ) results in
a 1?μV/LSb (Least Signi?cant Bit) resolution. Setting RA?=
RB?=?6.8 kΩ provides 111.6 μV/°C temperature coef?cient
(PT100 RTD with 0.385Ω/°C temperature coef?cient). This
provides 0.008°C/LSb temperature measurement resolution
for the entire range of 20Ω to 320Ω or -200°C to +800°C. A
single point calibration with a 0.1% 100Ω resistor provides
±0.1°C accuracy as shown in the ?gure below.
This approach provides a plug-and-play solution with
minimum adjustment. However, the system accuracy
depends on several factors such as the RTD type, biasing
circuit tolerance and stability, error due to power dissipation
or self-heat, and RTD non-linear characteristics.
RTD Instrumentation Circuit Block Diagram and Output Performance (see Application Note AN1154)
V DD
LDO
V LDO
0.1
C*
C*
1 μF
V DD
V REF
+
V REF
R B 5%
R A 1%
0.05
0
-0.05
PIC ?
MCU
3
SPI
MCP3551
–
RTD
-0.1
-200
0
200
400
600
800
Temperature (°C)
*See LDO Data Sheet at: www.microchip.com/LDO
12
Signal Chain Design Guide
相关PDF资料 |
PDF描述 |
|---|---|
| TSV250-130F-2 | POLYSWITCH PTC RESET 0.13A SMD |
| TSV250-130F-B-0.5-2 | POLYSWITCH PTC RESET 0.13A SMD |
| TURBO-DECO-XM-UT3 | SITE LICENSE TURBO DECODER XP |
| TVB058SA-L | SURGE PROTECTOR 58V DO-214AA |
| TVB200SA-L | SURGE PROTECTOR 200V BREAKOVER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TSSOP-28 | 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:16-BIT CCD/CIS ANALOG SIGNAL PROCESSOR |
| TSSOP-56 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Fairchild Semiconductor Product Package Material Disclosure |
| TSSOP-8 | 制造商:AOSMD 制造商全称:Alpha & Omega Semiconductors 功能描述:Tape and Reel Dimensions |
| TSSOP-8PIN | 制造商:IRF 制造商全称:International Rectifier 功能描述:Package Dimensions |
| TSSOP-B14J | 制造商:ROHM 制造商全称:Rohm 功能描述:IC Packages |
发布紧急采购，3分钟左右您将得到回复。