参数资料
型号: TVP5154PNPG4
厂商: TEXAS INSTRUMENTS INC
元件分类: 颜色信号转换
英文描述: COLOR SIGNAL DECODER, PQFP128
封装: PLASTIC, HTQFP-128
文件页数: 10/77页
文件大小: 795K
代理商: TVP5154PNPG4
www.ti.com
6
Clock Circuits
14.31818 MHz
14.31818-MHz
Crystal
124
123
CL1
CL2
R
1.8-V Clock
124
7
Genlock Control and RTC
F
dto +
F
ctrl
223
F
clk
(1)
7.1 TVP5154 Genlock Control Interface
7.2 RTC Mode
TVP5154
4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER
WITH INDEPENDENT SCALERS AND FAST LOCK
SLES163A – MARCH 2006 – REVISED JULY 2006
An internal line-locked PLL generates the system and pixel clocks. A 14.31818-MHz clock is required to
drive the PLL. This may be input to the TVP5154 decoder on terminal 124 (XIN), or a crystal of
14.31818-MHz fundamental resonant frequency may be connected across terminals 123 and 124 (XIN
and XOUT). Figure 6-1 shows the reference clock configurations. For the example crystal circuit shown (a
parallel-resonant crystal with 14.31818-MHz fundamental frequency), the external capacitors must have
the following relationship:
CL1 = CL2 = 2CL – CSTRAY
where CSTRAY is the terminal capacitance with respect to ground. Figure 6-1 shows the reference clock
configurations.
Figure 6-1. Clock and Crystal Connectivity
A Genlock control (GLCO) function is provided to support a standard video encoder to synchronize its
internal color oscillator for properly reproduced color with unstable timebase sources like VCRs.
The frequency control word of the internal color subcarrier digital control oscillator (DTO) and the
subcarrier phase reset bit are transmitted via the GLCO terminal. The frequency control word is a 23-bit
binary number. The frequency of the DTO can be calculated from the following equation:
where Fdto is the frequency of the DTO, Fctrl is the 23–bit DTO frequency control, and Fclk is the
frequency of the CLK.
A write of 1 to bit 4 of the chrominance control register at I2C subaddress 1Ah causes the subcarrier DTO
phase reset bit to be sent on the next scan line on GLCO. The active-low reset bit occurs seven CLKs
after the transmission of the last bit of DCO frequency control. Upon the transmission of the reset bit, the
phase of the TVP5154 internal subcarrier DCO is reset to zero.
A Genlock slave device can be connected to the GLCO terminal and uses the information on GLCO to
synchronize its internal color phase DCO to achieve clean line and color lock.
Figure 7-1 shows the timing diagram of the RTC mode. Clock rate for the RTC mode is four times slower
than the GLCO clock rate. For PLL frequency control, the upper 22 bits are used. Each frequency control
bit is two clock cycles long. The active-low reset bit occurs six CLKs after the transmission of the last bit of
PLL frequency control.
Clock Circuits
18
相关PDF资料
PDF描述
TVP5154PNPRG4 COLOR SIGNAL DECODER, PQFP128
TVP5154PNPR COLOR SIGNAL DECODER, PQFP128
TVP5154PNP COLOR SIGNAL DECODER, PQFP128
TVP5157PNPR COLOR SIGNAL DECODER, PQFP128
TVP5157PNP COLOR SIGNAL DECODER, PQFP128
相关代理商/技术参数
参数描述
TVP5154PNPR 功能描述:视频 IC 4Ch Lo Pwr PAL/NTSC SECAM Video Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel
TVP5154PNPRG4 制造商:TI 制造商全称:Texas Instruments 功能描述:4-CHANNEL LOW-POWER PAL/NTSC/SECAM VIDEO DECODER WITH INDEPENDENT SCALERS AND FAST LOCK
TVP5156PNP 功能描述:视频 IC 4Ch NTSC/PAL Video Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel
TVP5156PNPR 功能描述:视频 IC 4Ch NTSC/PAL Video Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel
TVP5157PNP 功能描述:视频 IC 4Ch NTSC/PAL Video Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel