- 您现在的位置：买卖IC网 > PDF目录18805 > TXE-418-KH2 (Linx Technologies Inc)TRANSMITTER RF 418MHZ SMT PDF资料下载
参数资料
| 型号： | TXE-418-KH2 |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 4/11页 |
| 文件大小： | 0K |
| 描述： | TRANSMITTER RF 418MHZ SMT |
| 产品变化通告： | Internal Componet Change 19/Jul/2010 |
| 标准包装： | 20 |
| 系列： | KH2 |
| 频率： | 418MHz |
| 应用： | 火警/安全警报，车库门开启器，RKE |
| 调制或协议： | ASK，OOK |
| 功率 - 输出： | -4dBm ~ 4dBm |
| 电流 - 传输： | 1.5mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 特点： | 内置遥控编码器 |
| 电源电压： | 2.7 V ~ 5.2 V |
| 工作温度： | -30°C ~ 70°C |
| 封装/外壳： | 表面安装 |
| 包装： | 管件 |
| 其它名称： | Q3387524 |
ENCODER OPERATION
POWER SUPPLY REQUIREMENTS
The KH2 Series transmitter internally utilizes
the HT640 encoder from Holtek. The
Power On
The module does not have an internal voltage
regulator; therefore it requires a clean, well-regulated
Vcc TO
MODULE
encoder begins a three-word transmission
cycle when the Transmission Enable line
(TE) is pulled high. This cycle will repeat
itself for as long as the TE line is held high.
Standby Mode
power source. While it is preferable to power the unit
from a battery, it can also be operated from a power
supply as long as noise is less than 20mV. Power
supply noise can affect the transmitter modulation;
Vcc IN
10 Ω
10 μ F
Once TE falls low, the encoder output
therefore, providing a clean power supply for the
A 10 Ω resistor in series with the supply followed by a
completes its final cycle and then stops as
shown in the Encoder / Decoder Timing
diagram. When a transmission enable signal
is applied, the encoder scans and transmits
the status of the 10 bits of the address code
and the 8 bits of the data serially in the order
A0 to A9, D0 to D7.
The status of each address / data pin can be
individually preset to logic high, low, or
floating. The floating state on the data input
is interpreted as logic low by the decoders
since the decoder output only has two
states. The address pins are usually set to
No
Transmission
Enabled?
Yes
3 Data Words
Transmitted
Transmission
Still Enabled?
3 Data Words
Transmitted
Continuously
module should be a high priority during design.
Figure 10: Supply Filter
10μF tantalum capacitor from V CC to ground will help in cases where the quality
of supply power is poor. These values may need to be adjusted depending on
the noise present on the supply line.
DATA INPUTS
When the Transmit Enable (TE) line goes high, the states of the eight data input
lines are recorded and encoded for transmission. The data lines are tri-state,
which means that they can be high, low, or floating, though the decoder will
interpret the floating state as a low. This feature means that the data lines do not
require pull-up or pull-down resistors. The states of the data lines can be set by
switches, jumpers, microcontrollers, or hardwired on the PCB.
switches or PCB wiring, while the data is
transmit particular security codes by DIP
Figure 8: Encoder Flowchart
selected using push buttons or electronic
switches. The floating state allows the KH2 transmitter to be used without pull-
up or pull-down resistors on the data and address input lines.
Encoder
Transmit
The encoder will send the states of the address and data lines three times. If the
TE line is still high, it will begin the cycle again. This means that the states of the
data lines are refreshed with each cycle, so the data lines can be changed
without having to pull TE low. There can be up to a 150mS lag in response as
the transmitter finishes one cycle then refreshes and starts over.
ENABLING TRANSMISSION
Enable
Encoder
< 1 Word
The module’s Transmit Enable (TE) line controls transmission status. When
taken high, the module initiates transmission, which continues until the line is
2
Data Out
Decoder VT
3 Words
2 Words
14
Transmitted Continuously
Clocks
3 Words
2
14
Clocks
pulled low or power to the module is removed. In some cases this line will be
wired permanently to V CC and transmission controlled by switching V CC to the
module. This is particularly useful in applications where the module powers up
and sends a transmission only when a button is pressed on the remote.
Decoder
Data Out
Check
Check
1/2 Clock Time
1/2 Clock Time
USING LADJ
The LADJ line allows the transmitter’s output power to be easily adjusted for
range control, lower power consumption, or to meet legal requirements. This is
Figure 9: Encoder / Decoder Timing Diagram
SETTING THE TRANSMITTER ADDRESS
The module provides ten tri-state address lines. This allows for the formation of
up to 59,049 (3 10 ) unique transmitter-receiver relationships. Tri-state means that
the address lines have three distinct states: high, low, or floating. These pins
may be hardwired or configured via a microprocessor, DIP switch, or jumpers.
The receiver’s address line states must match the transmitter’s exactly for a
transmission to be recognized. If the transmitted address does not match the
receiver’s local address, then the receiver will take no action.
Page 6
done by placing a resistor between GND and LADJ. When LADJ is connected
directly to GND, the output power will be at its maximum. Placing a resistor will
lower the output power by up to 7dB, as shown on Page 3 of this data guide.
This is very useful during FCC testing to compensate for antenna gain or other
product-specific issues that may cause the output power to exceed legal limits.
A variable resistor can be used so that the test lab can precicely adjust the output
power to the maximun level allowed by law. The resistor’s value can be noted
and a fixed resistor substituted for final testing. Even in designs where
attenuation is not anticipated, it is a good idea to place a resistor pad connected
to LADJ and GND so that it can be used if needed.
Page 7
相关PDF资料 |
PDF描述 |
|---|---|
| A1102LLHLT-T | IC SWITCH HALL EFFECT SOT23W |
| FXO-HC736R-58.9824 | OSC 58.9824 MHZ 3.3V HCMOS SMD |
| 9922-18BLK | LEAD PLUG STK BAN 2MM BLK 18" |
| GPTCRS01 | SWITCH ROLLER SPDT 15A SCRW TERM |
| MICRF112YMM | IC XMITTER UHF ASK/FSK 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TXE-433-KH | 功能描述:TRANSMITTER RF 433MHZ SMT RoHS:是 类别:RF/IF 和 RFID >> RF 发射器 系列:KH 标准包装:4,000 系列:- 频率:310MHz ~ 440MHz 应用:- 调制或协议:UHF，ASK 数据传输率 - 最大:20 kBaud 功率 - 输出:1dBm ~ 5dBm 电流 - 传输:10mA 数据接口:PCB，表面贴装 天线连接器:PCB，表面贴装 存储容量:- 特点:- 电源电压:2.2 V ~ 4 V 工作温度:-40°C ~ 85°C 封装/外壳:16-LSSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| TXE-433-KH2 | 功能描述:射频模块 RF Transmitter 433MHz RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| TXEAACSANF-40.000000 | 功能描述:40MHz Clipped Sine Wave VCTCXO Oscillator Surface Mount 2.8 V ~ 3.3 V 2.5mA 制造商:taitien 系列:TX 包装:剪切带（CT） 零件状态:新产品 类型:VCTCXO 频率:40MHz 功能:- 输出:削峰正弦波 电压 - 电源:2.8 V ~ 3.3 V 频率稳定度:±500ppb 工作温度:-20°C ~ 70°C 电流 - 电源（最大值）:2.5mA 等级:- 安装类型:表面贴装 大小/尺寸:0.126" 长 x 0.098" 宽（3.20mm x 2.50mm） 高度:0.039"（1.00mm） 封装/外壳:4-SMD，无引线（DFN，LCC） 电流 - 电源（禁用）（最大值）:- 标准包装:1 |
| TXEAADSANF-20.000000 | 功能描述:20MHz Clipped Sine Wave VCTCXO Oscillator Surface Mount 2.8 V ~ 3.3 V 2mA 制造商:taitien 系列:TX 包装:剪切带（CT） 零件状态:新产品 类型:VCTCXO 频率:20MHz 功能:- 输出:削峰正弦波 电压 - 电源:2.8 V ~ 3.3 V 频率稳定度:±500ppb 工作温度:-30°C ~ 85°C 电流 - 电源（最大值）:2mA 等级:- 安装类型:表面贴装 大小/尺寸:0.126" 长 x 0.098" 宽（3.20mm x 2.50mm） 高度:0.039"（1.00mm） 封装/外壳:4-SMD，无引线（DFN，LCC） 电流 - 电源（禁用）（最大值）:- 标准包装:1 |
| TXEAADSANF-25.000000 | 功能描述:25MHz Clipped Sine Wave VCTCXO Oscillator Surface Mount 2.8 V ~ 3.3 V 2mA 制造商:taitien 系列:TX 包装:剪切带（CT） 零件状态:新产品 类型:VCTCXO 频率:25MHz 功能:- 输出:削峰正弦波 电压 - 电源:2.8 V ~ 3.3 V 频率稳定度:±500ppb 工作温度:-30°C ~ 85°C 电流 - 电源（最大值）:2mA 等级:- 安装类型:表面贴装 大小/尺寸:0.126" 长 x 0.098" 宽（3.20mm x 2.50mm） 高度:0.039"（1.00mm） 封装/外壳:4-SMD，无引线（DFN，LCC） 电流 - 电源（禁用）（最大值）:- 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。