- 您现在的位置：买卖IC网 > PDF目录373750 > TZA3011A TRANSIL PDF资料下载
参数资料
| 型号： | TZA3011A |
| 英文描述： | TRANSIL |
| 中文描述： | 30 Mbits /秒高达3.2 Gb /秒阿率（商标）激光驱动器 |
| 文件页数： | 24/28页 |
| 文件大小： | 138K |
| 代理商： | TZA3011A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页
2003 Apr 02
24
Philips Semiconductors
Product specification
30 Mbits/s up to 3.2 Gbits/s
A-rate
TM
laser drivers
TZA3011A; TZA3011B
15 SOLDERING
15.1
Introduction to soldering surface mount
packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certainsurfacemountICs,butitisnotsuitableforfinepitch
SMDs. In these situations reflow soldering is
recommended.
15.2
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 250
°
C. The top-surface temperature of the
packages should preferably be kept:
below 220
°
C for all the BGA packages and packages
with a thickness
≥
2.5mm and packages with a
thickness <2.5 mm and a volume
≥
350 mm
3
so called
thick/large packages
below 235
°
C for packages with a thickness <2.5 mm
and a volume <350 mm
3
so called small/thin packages.
15.3
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
15.4
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相关PDF资料 |
PDF描述 |
|---|---|
| TZA3019AVH | TRANSIL |
| TZA3019BVH | TRANSIL |
| TZA3019CVH | TRANSIL |
| TZA3015HW | 30 Mbit/s to 3.2 Gbit/s A-rate 4-bit fibre optic transceiver |
| Z00607DA | SENSITIVE GATE TRIACS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TZA3011AVH/C2,551 | 功能描述:激光驱动器 3.3V D-LOOP LASERDRVR DC-3.2GB RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| TZA3011AVH/C2,557 | 功能描述:激光驱动器 3.3V D-LOOP LASERDRVR DC-3.2GB RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| TZA3011BVH/C2,551 | 功能描述:激光驱动器 3.3V D-LOOP LASERDRVR DC-3.2GB RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| TZA3011BVH/C2,557 | 功能描述:激光驱动器 3.3V D-LOOP LASERDRVR DC-3.2GB RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| TZA3012AHW | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:30 Mbits/s up to 3.2 Gbits/s A-rateTM Fibre Optic Receiver |
发布紧急采购，3分钟左右您将得到回复。