- 您现在的位置：买卖IC网 > Datasheet目录367 > UBA2032TS/N2,118 (NXP Semiconductors)IC DRIVER FULL BRIDGE 28-SSOP Datasheet资料下载
参数资料
| 型号： | UBA2032TS/N2,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 18/21页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER FULL BRIDGE 28-SSOP |
| 标准包装： | 1,000 |
| 配置： | 半桥 |
| 输入类型： | 自振荡 |
| 电流 - 峰： | 130mA |
| 配置数： | 1 |
| 输出数： | 4 |
| 高端电压 - 最大（自引导启动）： | 550V |
| 电源电压： | 10.5 V ~ 13.5 V |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 带卷 (TR) |
| 其它名称： | 935270517118 UBA2032TSDB-T UBA2032TSDB-T-ND |
Philips Semiconductors
Full bridge driver IC
SOLDERING
Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is
recommended.
Re?ow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Driven by legislation and environmental forces the
worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 seconds and 200 seconds
depending on heating method.
Typical reflow peak temperatures range from
215 ° C to 270 ° C depending on solder paste material. The
top-surface temperature of the packages should
preferably be kept:
? below 225 ° C (SnPb process) or below 245 ° C (Pb-free
process)
– for all BGA, HTSSON..T and SSOP..T packages
– for packages with a thickness ≥ 2.5 mm
– for packages with a thickness < 2.5 mm and a
volume ≥ 350 mm 3 so called thick/large packages.
? below 240 ° C (SnPb process) or below 260 ° C (Pb-free
process) for packages with a thickness < 2.5 mm and a
volume < 350 mm 3 so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing,
must be respected at all times.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
2005 Mar 24
18
Product speci?cation
UBA2032
If wave soldering is used the following conditions must be
observed for optimal results:
? Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
? For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
? For packages with leads on four sides, the footprint must
be placed at a 45 ° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time of the leads in the wave ranges from
3 seconds to 4 seconds at 250 ° C or 265 ° C, depending
on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300 ° C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 seconds to 5 seconds
between 270 ° C and 320 ° C.
相关PDF资料 |
PDF描述 |
|---|---|
| UBA2033TS/N2,118 | IC FULL BRIDGE DRIVER 28-SSOP |
| UBA3070T/N1,118 | IC LED DVR WHITE BCKLGT 8-SOIC |
| UEVM4430G-01-00-00 | PANDABOARD |
| UEVM4460G-02-01-00 | PANDABOARD ES |
| UHDM7218BPA | PLATE BARRIER 71.86X17.87" GRY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UBA2033 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:HF full bridge driver IC |
| UBA2033TS | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:HF full bridge driver IC |
| UBA2033TS/N2,118 | 功能描述:功率驱动器IC LIGHTING HID DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| UBA2033TS/N2-T | 功能描述:功率驱动器IC LIGHTING HID DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| UBA2033TS/N3,118 | 功能描述:功率驱动器IC UBA2033TS/SSOP28/REEL13//N3 RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。