- 您现在的位置：买卖IC网 > PDF目录378724 > UCC2888DTR Precision 1 A regulators PDF资料下载
参数资料
| 型号： | UCC2888DTR |
| 英文描述： | Precision 1 A regulators |
| 中文描述： | 电压模式开关电源控制器 |
| 文件页数： | 5/19页 |
| 文件大小： | 296K |
| 代理商： | UCC2888DTR |
SLUS458C AUGUST 2001 REVISED SEPTEMBER 2003
5
www.ti.com
pin assignments
COMP:
This pin provides the output of the error amplifier for compensation. In addition, the COMP pin is
frequently used as a control port by utilizing a secondary-side error amplifier to send an error signal across the
secondary-primary isolation boundary through an opto-isolator.
CS:
The current sense pin is the non-inverting input to the PWM comparator. This is compared to a signal
proportional to the error amplifier output voltage. A voltage ramp can be applied to this pin to run the device with
a voltage mode control configuration.
FB:
This pin is the inverting input to the error amplifier. The non-inverting input to the error amplifier is internally
trimmed to 2.5 V
±
1%.
GND:
Ground return pin for the output driver stage and the logic level controller section.
OUT:
The output of the on-chip drive stage. OUT is intended to directly drive a MOSFET. The OUT pin in the
UCC38C40, UCC38C42 and UCC38C43 is the same frequency as the oscillator, and can operate near 100%
duty cycle. In the UCC38C41, UCC38C44 and the UCC38C45, the frequency of OUT is one-half that of the
oscillator due to an internal T flipflop. This limits the maximum duty cycle to < 50%.
RT/CT:
Timing resistor and timing capacitor. The timing capacitor should be connected to the device ground
using minimal trace length.
VDD:
Power supply pin for the device. This pin should be bypassed with a 0.1-
μ
F capacitor with minimal trace
lengths. Additional capacitance may be needed to provide hold up power to the device during startup.
VREF:
5-V reference. For stability, the reference should be bypassed with a 0.1-
μ
F capacitor to ground using
the minimal trace length possible.
相关PDF资料 |
PDF描述 |
|---|---|
| UCC2888J | Precision 1 A regulators |
| UCC2888N | Precision 1 A regulators |
| UCC380000PW | Medium current 1.2 to 37 V adjustable voltage regulator |
| UCC380000PWTR | High precision voltage regulator |
| UCC380001D | High precision voltage regulator |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UCC2889D | 功能描述:电压模式 PWM 控制器 Off-line Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| UCC2889DG4 | 功能描述:电压模式 PWM 控制器 Off-line Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| UCC2889DTR | 功能描述:电压模式 PWM 控制器 Off-line Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| UCC2889DTR/81361 | 制造商:Texas Instruments 功能描述: |
| UCC2889DTRG4 | 功能描述:电压模式 PWM 控制器 Off-line Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。