参数资料
型号: UCC2893PWG4
厂商: Texas Instruments
文件页数: 17/41页
文件大小: 0K
描述: IC REG CTRLR FLYBK ISO 16-TSSOP
标准包装: 90
PWM 型: 电流模式
输出数: 1
频率 - 最大: 1MHz
占空比: 74%
电源电压: 8.5 V ~ 16 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 125°C
封装/外壳: 16-TSSOP(0.173",4.40mm 宽)
包装: 管件
UCC2891, UCC2892
UCC2893, UCC2894
SLUS542F ? OCTOBER 2003 ? REVISED JULY 2009
FUNCTIONAL DESCRIPTION
Synchronization
The UCC2891 family has a synchronization input pin which can be used to synchronize their oscillator to a
constant frequency system clock. The synchronization signal must have a higher frequency than the free
running oscillator frequency and can be either in-phase or out-of-phase for interleaved operation.
The operation of the oscillator and relevant other waveforms in free running and synchronized mode are shown
in Figure 6.
SYNC
CT
DMAX
OUT
AUX
UDG?03152
Figure 6. Synchronization Waveforms, P?Channel
The most critical and unique feature of the oscillator is to limit the maximum operating duty cycle of the converter.
It is achieved by accurately controlling the charge and discharge intervals of the on board timing capacitor. The
maximum on-time of OUT (pin 13), which is also the maximum duty cycle of the active clamp converter is limited
by the charging interval of the timing capacitor. While the capacitor is being reset to its initial voltage level OUT
is guaranteed to be off.
When synchronization is used, the rising edge of the signal terminates the charging period and initiate the
discharge of the timing capacitor. Once the timing capacitor voltage reaches the predefined valley voltage, a
new charge period starts automatically. This method of synchronization leaves the charge and discharge slopes
of the timing waveform unaffected thus maintains the maximum duty cycle of the converter, independent of the
mode of operation.
Although the synchronization circuit is level sensitive, the actual synchronization event occurs at the rising edge
of the waveform. This allows the synchronizing pulse width to vary significantly but certain limitations must be
observed. The minimum pulse width should be sufficient to guarantee reliable triggering of the internal oscillator
circuitry, therefore it should be greater than approximately 50 nanoseconds. The other limiting factor is to keep
it shorter than 1 * D MAX
T SYNC where T SYNC is the period of the synchronization frequency.
www.ti.com
17
相关PDF资料
PDF描述
VE-21M-EY-F1 CONVERTER MOD DC/DC 10V 50W
ISC1210BN1R2J INDUCTOR WW 1.2UH 5% 1210
EGM22DTKH CONN EDGECARD 44POS DIP .156 SLD
VI-21M-EY-F3 CONVERTER MOD DC/DC 10V 50W
ISC1812RQ391K INDUCTOR WW 390UH 10% 1812
相关代理商/技术参数
参数描述
UCC2893PWR 功能描述:电流型 PWM 控制器 Crnt Mode Active Clamp PWM Cntrlr RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
UCC2893PWRG4 功能描述:电流型 PWM 控制器 Crnt Mode Active Clamp PWM Cntrlr RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
UCC2894D 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
UCC2894DG4 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
UCC2894DR 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14