- 您现在的位置：买卖IC网 > PDF目录20837 > UCH-3.3/35-D24PB-C (Murata Power Solutions Inc)CONV DC/DC 115.5W 3.3V 35A PDF资料下载
参数资料
| 型号： | UCH-3.3/35-D24PB-C |
| 厂商： | Murata Power Solutions Inc |
| 文件页数： | 8/18页 |
| 文件大小： | 0K |
| 描述： | CONV DC/DC 115.5W 3.3V 35A |
| 标准包装： | 36 |
| 系列： | UCH |
| 类型： | 隔离 |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 18V |
| 电压 - 输入（最大）： | 36V |
| Voltage - Output 1： | 3.3V |
| 电流 - 输出（最大）： | 35A |
| 电源（瓦） - 制造商系列： | 115W |
| 电压 - 隔离： | 2.25kV（2250V） |
| 安装类型： | 通孔 |
| 封装/外壳： | 9-DIP 模块，1/2 砖 |
| 尺寸/尺寸： | 2.40" L x 2.30" W x 0.40" H（61.0mm x 58.4mm x 10.2mm） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
| 效率： | 89% |
| 电源（瓦特）- 最大： | 115.5W |
| 产品目录页面： | 2719 (CN2011-ZH PDF) |
| 其它名称： | 811-1848-5 |
Single Output UCH Models
Isolated, “Half-Brick”
1.8?15V Output DC/DC Converters
Absolute Maximum Ratings
Input Voltage:
D24 Models -
D48 Models -
Volts, max. continuous
Volts, transient, 100 mSec
Volts, max. continuous
0-36 VDC
50 VDC
0-75 VDC
Volts, transient, 100 mSec
On/Off Control
Input Reverse-Polarity Protection
Output Overvoltage
Output Current
Overtemperature Protection
Storage Temperature
Lead Temperature
100 VDC
-0.7 V. min to +15V max.
None. Install external fuse.
Vout nom. +20% max.
Current-limited. Devices can
withstand sustained short
circuit without damage. The
outputs are not intended to
accept appreciable reverse
current.
Device includes electronic
overtemperature shutdown
protection under normal
operation.
-55 to +125 ° C
See soldering speci?cations
These are stress ratings. Exposure of devices to greater than any of these conditions may
adversely affect long-term reliability. Proper operation under conditions other than those
listed in the Performance/Functional Speci?cations Table is not implied.
Speci?cation Notes:
(1) All models are tested and speci?ed with external 1 μF paralleled with 10 μF output capacitors
and no external input capacitor. All capacitors are low ESR types. These capacitors are necessary to
accommodate our test equipment and may not be required to achieve speci?ed performance in your
applications. All models are stable and regulate within spec under no-load conditions.
(9) All models are fully operational and meet published speci?cations, including “cold start” at –40°C.
At full power, the package temperature of all on-board components must not exceed +128°C.
(10) Regulation speci?cations describe the deviation as the line input voltage or output load current is
varied from a nominal midpoint value to either extreme.
All speci?cations are typical unless noted. General conditions for Speci?cations are +25°C,
Vin=nominal, Vout=nominal, full load. Adequate air?ow must be supplied for extended testing under
power.
(2) Input Back Ripple Current is tested and speci?ed over a 5 Hz to 20 MHz bandwidth. Input ?ltering
is Cin=33 μF, 100V, Cbus=220 μ F, 100V, Lbus=12 μH.
(3) Note that Maximum Power Derating curves indicate an average current at nominal input voltage.
At higher temperatures and/or lower air?ow, the DC/DC converter will tolerate brief full current outputs
if the total RMS current over time does not exceed the Derating curve. All Derating curves are pre-
(11) The output overvoltage protection is automatic recovery. The overvoltage may occur either from
internal failure or from an external forcing voltage as in a shared power system.
(12) Output current limit and short circuit protection is non-latching. When the overcurrent fault is
removed, the converter will immediately recover. After an output overcurrent or short circuit, “hiccup”
operation repeatedly attempts to restart the converter with a brief, full-current output. If the overcurrent
condition still exists, the restart current will be removed and then tried again. This short current pulse
prevents overheating and damaging the converter. Once the fault is removed, the converter immedi-
ately resumes normal operation.
sented at sea level altitude. Be aware of reduced power dissipation with increasing altitude.
(13) Do not exceed maximum power speci?cations when adjusting the output trim.
(4) Mean Time Before Failure is calculated using the Telcordia (Belcore) SR-332 Method 1, Case 3,
ground ?xed conditions, Tpcboard=+25 ° C, full load, natural air convection.
(14) At zero output current, the output may contain low frequency components which exceed the
ripple speci?cation. The output may be operated inde?nitely with no load.
(5) The On/Off Control is normally selected by a switch or an open collector or open drain transistor.
But it may also be driven with external logic or by applying appropriate external voltages which are
referenced to Input Common and comply with the On/Off voltage speci?cations.
(15) If reverse polarity is accidentally applied to the input, to ensure reverse input protection with full
output load, always connect an external input fuse in series with the +Vin input. Use approximately
twice the full input current rating with nominal input voltage.
(6) Output current limiting begins when the output voltage degrades approximately 2% from the
selected setting.
(16) Output accuracy is dependent on user-supplied trim resistors. To achieve high accuracy, use ±1%
or better tolerance metal-?lm resistors mounted close to the converter.
(7) The outputs are not intended to sink appreciable reverse current.
(17) Normally, the Sense lines are connected at the remote load to compensate for IR voltage drops
(8) Output noise may be further reduced by adding an external ?lter. Logic circuits with low power
voltages may have a small voltage margin between logic ZERO and logic ONE, requiring noise sup-
pression. Use only as much output ?ltering as needed to achieve your noise requirements. Excessive
output capacitance can retard transient response or possibly cause instability. Low ESR ceramic
capacitors may degrade dynamic performance. Be sure to thoroughly test your system under full load
with all components installed.
in the power wiring and to improve dynamic response. If Sense is not used, each Sense pin should be
connected at the converter to its respective Vout pin.
CAUTION: This product is not internally fused. To comply with safety agency certi?cations and to
avoid injury to personnel or equipment, the user must connect an external fast-blow fuse to the input
terminals.
www.murata-ps.com/support
MDC_UCH Models.C01 Page 8 of 18
相关PDF资料 |
PDF描述 |
|---|---|
| P51-750-S-H-P-4.5OVP-000-000 | SENSOR 750PSI M12-1.5 6G .5-4.5V |
| P51-1000-S-D-M12-4.5V-000-000 | SENSOR 1000PSI 7/16-20 UNF 4.5V |
| CEFA103-G | DIODE FAST 1A 200V DO-214AC |
| REC3-1215SRW/H4/C/SMD | CONV DC/DC 3W 9-18VIN 15VOUT |
| P51-750-S-D-M12-4.5V-000-000 | SENSOR 750PSI 7/16-20 UNF 4.5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UCH42 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:TRIODE-HEXODE FOR USE AS FREQUENCY CHANGER AND PHASE INVERTER |
| UCH-5/10-D48NB-C | 功能描述:DC/DC转换器 48Vin 5Vout 10A 50W Neg Plty W/Baseplate RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| UCH-5/10-D48NB-C | 制造商:Murata Power Solutions 功能描述:DC/DC Converter |
| UCH-5/10-D48N-C | 功能描述:DC/DC转换器 5Vout 10A 50W 48Vin Neg Polarity RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| UCH-5/10-D48PB-C | 功能描述:DC/DC转换器 48Vin 5Vout 10A 50W pos polrty w/Baseplt RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。