- 您现在的位置：买卖IC网 > PDF目录8089 > UEI25-033-D48PM-C (Murata Power Solutions Inc)36-75VIN 3.3VOUT 25W POS LOG SMD PDF资料下载
参数资料
| 型号： | UEI25-033-D48PM-C |
| 厂商： | Murata Power Solutions Inc |
| 文件页数： | 21/24页 |
| 文件大小： | 0K |
| 描述： | 36-75VIN 3.3VOUT 25W POS LOG SMD |
| 标准包装： | 100 |
| 系列： | UEI25 |
| 类型： | 隔离 |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 36V |
| 电压 - 输入（最大）： | 75V |
| Voltage - Output 1： | 3.3V |
| 电流 - 输出（最大）： | 7.5A |
| 电源（瓦） - 制造商系列： | 25W |
| 电压 - 隔离： | 2.25kV（2250V） |
| 特点： | 具有远程开/关功能 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-SMD 模块，1x1 砖 |
| 尺寸/尺寸： | 1.10" L x 0.96" W x 0.34" H（27.9mm x 24.4mm x 8.7mm） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
| 效率： | 89.5% |
| 电源（瓦特）- 最大： | 25W |
UEI25 Series
Single Output Isolated 25-Watt DC/DC Converters
There are two CAUTIONs to observe for the Trim input:
CAUTION : To avoid unplanned power down cycles, do not exceed EITHER the
maximum output voltage OR the maximum output power when setting the trim.
If the output voltage is excessive, the OVP circuit may inadvertantly shut down
the converter. If the maximum power is exceeded, the converter may enter
current limiting. If the power is exceeded for an extended period, the converter
may overheat and encounter overtemperature shut down.
CAUTION : Be careful of external electrical noise. The Trim input is a senstive
input to the converter’s feedback control loop. Excessive electrical noise may
cause instability or oscillation. Keep external connections short to the Trim
There are two CAUTIONs for the On/Off Control:
CAUTION: While it is possible to control the On/Off with external logic if you
carefully observe the voltage levels, the preferred circuit is either an open
drain/open collector transistor or a relay (which can thereupon be controlled by
logic). The On/Off prefers to be set at approx. +15V (open pin) for the ON state,
assuming positive logic.
CAUTION: Do not apply voltages to the On/Off pin when there is no input
power voltage. Otherwise the converter may be permanently damaged.
input. Use shielding if needed.
Trim Equations
Trim Up
Trim Down
+VIN
+VOUT
UEI25-033-D48
ON/OFF
CONTROL
TRIM
R TRIM DOWN
LOAD
R TUP (Ω) =
12775
V O – 3.3
– 2050
R TDOWN (Ω) =
5110 x (Vo – 2.5)
3.3 – V O
– 2050
UEI25-050-D48
?VIN
?VOUT
R TUP (Ω) =
12775
V O – 5
– 2050
R TDOWN (Ω) =
5110 x (Vo –2.5)
5 – V O
– 2050
Figure 4. Trim adjustments to decrease Output Voltage using a Fixed Resistor
UEI25-120-D48
+VIN
+VOUT
R TUP (Ω) =
25000
V O – 12
– 5110
R TDOWN (Ω) =
10000 (Vo-2.5)
12 – V O
– 5110
<Connect trim resistor
<Connect trim resistor
ON/OFF
CONTROL
TRIM
R TRIM UP
LOAD
between Trim and –Vout>
between Trim and +Vout>
Where Vo = Desired output voltage. Adjustment accuracy is subject to resis-
tor tolerances and factory-adjusted output accuracy. Mount trim resistor close
to converter. Use short leads.
?VIN
?VOUT
Remote On/Off Control
Figure 5. Trim adjustments to increase Output Voltage using a Fixed Resistor
On the input side, a remote On/Off Control can be speci?ed with either positive
or negative logic as follows:
+VCC
Positive : Models equipped with Positive Logic are enabled when the On/Off
pin is left open or is pulled high to +15V DC with respect to –V IN . An internal bias
current causes the open pin to rise to +V IN . Positive-logic devices are disabled
when the On/Off is grounded or brought to within a low voltage (see Speci?ca-
tions) with respect to –V IN .
Negative: Models with negative logic are on (enabled) when the On/Off is
grounded or brought to within a low voltage (see Speci?cations) with respect to
–V IN . The device is off (disabled) when the On/Off is left open or is pulled high
to +15V DC Max. with respect to –V IN .
ON/OFF
CONTROL
-VIN
Figure 6. Driving the On/Off Control Pin (suggested circuit)
Dynamic control of the On/Off function should be able to sink the speci?ed
signal current when brought low and withstand speci?ed voltage when brought
high. Be aware too that there is a ?nite time in milliseconds (see Speci?cations)
between the time of On/Off Control activation and stable, regulated output. This
time will vary slightly with output load type and current and input conditions.
www.murata-ps.com/support
MDC_UEI25W.B09 Page 21 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| SQM48T25010-PDA0 | DC/DC EIGHTH BRICK |
| SQM48T25010-PDCP | DC/DC EIGHTH BRICK |
| MC74VHC540DWR2G | IC INVERTER 8-INPUT 20SOIC |
| OSTV7223250 | TERM BLOCK PLUG 3.81MM 22POS |
| OSTV7221250 | TERM BLOCK PLUG 3.50MM 22POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UEI25-050-D48 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:Single Output Isolated 25-Watt DC/DC Converters |
| UEI25-050-D48N-C | 功能描述:DC/DC转换器 48Vin 5Vout 5A 25W Neg. Polarity RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| UEI25-050-D48NM-C | 功能描述:DC/DC转换器 48Vin 5Vout 5A SMT 25W Neg. Polarity RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| UEI25-050-D48P-C | 功能描述:DC/DC转换器 48Vin 5Vout 5A 25W Pos. Polarity RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| UEI25-050-D48PM-C | 功能描述:DC/DC转换器 48Vin 5Vout 5A SMT 25W Pos. Polarity RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。