- 您现在的位置：买卖IC网 > Datasheet目录530 > UPC8179TB-EV24 (CEL)EVAL BOARD FOR UPC8179TB 2.4GHZ Datasheet资料下载
参数资料
| 型号： | UPC8179TB-EV24 |
| 厂商： | CEL |
| 文件页数： | 2/11页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR UPC8179TB 2.4GHZ |
| 标准包装： | 1 |
| 类型： | 放大器 |
| 频率： | 100MHz ~ 2.4GHz |
| 适用于相关产品： | UPC8179TB@2.4GHz |
| 已供物品： | 板 |
UPC8179TB
ABSOLUTE MAXIMUM RATINGS 1 (T A = 25 ° C)
RECOMMENDED
SYMBOLS
PARAMETERS
UNITS
RATINGS
OPERATING CONDITIONS
V CC
Supply Voltage, Pins 4 & 6
V
3.6
SYMBOLS
PARAMETERS
UNITS MIN
TYP MAX
I CC
Circuit Current
mA
15
V CC
Supply Voltage
V
2.7
3.0
3.3
P D
Power
Dissipation 2
mW
270
T A
Operating Ambient
° C
-40
+25
+85
T OP
T STG
P IN
Operating Temperature
Storage Temperature
Input Power
° C
° C
dBm
-40 to +85
-55 to +150
+5
Temperature
Notes:
1. Operation in excess of any one of these parameters may result
in permanent damage.
2. Mounted on a 50 x 50 x 1.6 mm epoxy glass PWB (T A = +85 ° C).
PIN FUNCTIONS
Pin No.
1
Symbol
INPUT
Pin Voltage
1.09 V
Description
Signal Input Pin. A internal
matching circuit, configured with
Internal Equivalent Circuit
resistors, enable 50 W connection
over a wide band. This pin must
be coupled to signal source with
capacitor for DC cut.
6
2
GND
through external inductor
Ground pin. This pin should be
4
3
5
connected to the system ground with
minimum inductance. Ground pattern
on the board should be formed as
wide as possible. All the ground pins
must be connected together with
wide ground pattern to decrease
impedance difference.
4
OUTPUT
Same as V CC voltage
Signal output pin. This pin is
designed as collector output. Due
to the high impedance output, this
pin should be externally equipped
3
1
2
5
with matching LC matching circuit
to next stage. For L, a size 1005
chip inductor can be chosen.
6
V CC
2.4 to 3.3
Power supply pin. This pin should
be externally equipped with bypass
capacitor to minimize its impedance.
TYPICAL PERFORMANCE CURVES (Unless otherwise specified, T A = 25 ? C)
5
4
3
2
1
0
CIRCUIT CURRENT vs. VOLTAGE
No signals
CIRCUIT CURRENT vs. TEMPERATURE
5
No signals
Vcc = 3.0 V
4
3
2
1
0
0
1
2
3
4
–60
–40
–20
0
+20
+40
+60
+80
+100
Voltage, V CC (V)
Temperature, T A ( ° C)
相关PDF资料 |
PDF描述 |
|---|---|
| UPC8179TK-E2-A | IC MMIC AMP 6-MINIMOLD |
| UPC8181TB-E3-A | IC MMIC AMP 6-SUPER MINIMOLD |
| UPC8182TB-E3-A | IC MMIC AMP 6-SUPER MINIMOLD |
| UPC8187TB-EV24 | EVAL BOARD UPC8187TB 2.4GHZ |
| UPC8190K-EVAL | EVAL BOARD FOR UPC8190K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UPC8179TK | 功能描述:射频放大器 Lo-Current Amplifier RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| UPC8179TK-A | 功能描述:射频放大器 Lo-Current Amplifier RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| UPC8179TK-E1 | 制造商:California Eastern Laboratories (CEL) 功能描述:USE UPC8179TK-E2, 5K/REEL |
| UPC8179TK-E2 | 功能描述:射频放大器 Lo-Current Amplifier RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| UPC8179TK-E2-A | 功能描述:射频放大器 Lo-Current Amplifier RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。