- 您现在的位置：买卖IC网 > PDF目录378741 > UPD65812-QFP160P1.2SQ ASIC PDF资料下载
参数资料
| 型号： | UPD65812-QFP160P1.2SQ |
| 英文描述： | ASIC |
| 中文描述： | 专用集成电路 |
| 文件页数： | 23/64页 |
| 文件大小： | 399K |
| 代理商： | UPD65812-QFP160P1.2SQ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
23
μ
PD64A, 65
Data Sheet U14380EJ2V0DS00
5.2 Standby Mode Setup and Release
The standby mode is set with the HALT #b
3
b
2
b
1
b
0
B instruction for both STOP mode and HALT mode. For the
standby mode to be set, the status flag (F) is required to have been cleared (to 0).
The standby mode is released by the release condition specified with the reset (POC) or the operand of HALT
instruction. If the standby mode is released, the status flag (F) is set (to 1).
Even when the HALT instruction is executed in the state that the status flag (F) has been set (to 1), the standby
mode is not set. If the release condition is not met at this time, the status flag is cleared (to 0). If the release condition
is met, the status flag remains set (to 1).
Even in the case when the release condition has been already met at the point that the HALT instruction is
executed, the standby mode is not set. Here, also, the status flag (F) is set (to 1).
Caution Depending on the status of the status flag (F), the HALT instruction may not be executed. Be
careful about this. For example, when setting HALT mode after checking the key status with
the STTS instruction, the system does not enter HALT mode as long as the status flag (F)
remains set (to 1) thus sometimes performing an unintended operation. In this case, the
intended operation can be realized by executing the STTS instruction immediately after timer
setting to clear (to 0) the status flag.
Example
STTS
#03H
;To check the K
I
pin status.
MOV
STTS
T, #0xxH
#05H
(During this time, be sure not to execute an instruction that may set the status flag.)
#05H
;To set HALT mode
;To set the timer
;To clear the status flag
HALT
Table 5-2. Addresses Executed after Standby Mode Release
Release Condition
Address Executed after Release
Reset
0 address
Release condition shown in Table 5-3
The address following the HALT instruction
…
…
相关PDF资料 |
PDF描述 |
|---|---|
| UPD65813 | ASIC |
| UPD65813-QFP160P1.2SQ | ASIC |
| UPD65823-QFP120P1.2SQ | ASIC |
| UPD65823-QFP160P1.2SQ | ASIC |
| UPD65825-QFP120P1.2SQ | ASIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UPD65813 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:ASIC |
| UPD65813-QFP160P1.2SQ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:ASIC |
| UPD65823-QFP120P1.2SQ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:ASIC |
| UPD65823-QFP160P1.2SQ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:ASIC |
| UPD65825-QFP120P1.2SQ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:ASIC |
发布紧急采购，3分钟左右您将得到回复。