- 您现在的位置：买卖IC网 > PDF目录361590 > UPSD3212AV-40U6T (意法半导体) Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic PDF资料下载
参数资料
| 型号： | UPSD3212AV-40U6T |
| 厂商： | 意法半导体 |
| 英文描述： | Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| 中文描述： | 闪存可编程系统设备与8032具有USB和可编程逻辑控制器 |
| 文件页数： | 25/163页 |
| 文件大小： | 2844K |
| 代理商： | UPSD3212AV-40U6T |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页
25/163
uPSD3212A, uPSD3212C, uPSD3212CV
Table
14
shows the list of conditional jumps avail-
able to the uPSD321x Devices user. All of these
jumps specify the destination address by the rela-
tive offset method, and so are limited to a jump dis-
tance of -128 to +127 bytes from the instruction
following the conditional jump instruction. Impor-
tant to note, however, the user specifies to the as-
sembler the actual destination address the same
way as the other jumps: as a label or a 16-bit con-
stant.
There is no Zero Bit in the PSW. The JZ and JNZ
instructions test the Accumulator data for that con-
dition.
The DJNZ instruction (Decrement and Jump if Not
Zero) is for loop control. To execute a loop N
times, load a counter byte with N and terminate the
loop with a DJNZ to the beginning of the loop, as
shown below for N = 10:
MOV COUNTER,#10
LOOP: (begin loop)
(end loop)
DJNZ COUNTER, LOOP
(continue)
The CJNE instruction (Compare and Jump if Not
Equal) can also be used for loop control as in
Ta-
ble 9., page 21
. Two bytes are specified in the op-
erand field of the instruction. The jump is executed
only if the two bytes are not equal. In the example
of
Table 9., page 21
Shifting a BCD Number One
Digits to the Right, the two bytes were data in R1
and the constant 2Ah. The initial data in R1 was
2Eh.
Every time the loop was executed, R1 was decre-
mented, and the looping was to continue until the
R1 data reached 2Ah.
Another application of this instruction is in “greater
than, less than” comparisons. The two bytes in the
operand field are taken as unsigned integers. If the
first is less than the second, then the Carry Bit is
set (1). If the first is greater than or equal to the
second, then the Carry Bit is cleared.
Machine Cycles
A machine cycle consists of a sequence of six
states, numbered S1 through S6. Each state time
lasts for two oscillator periods. Thus, a machine
cycle takes 12 oscillator periods or 1μs if the oscil-
lator frequency is 12MHz. Refer to
Figure
14., page 26
.
Each state is divided into a Phase 1 half and a
Phase 2 half. State Sequence in uPSD321x Devic-
es shows that retrieve/execute sequences in
states and phases for various kinds of instructions.
Normally two program retrievals are generated
during each machine cycle, even if the instruction
being executed does not require it. If the instruc-
tion being executed does not need more code
bytes, the CPU simply ignores the extra retrieval,
and the Program Counter is not incremented.
Execution of a one-cycle instruction (
Figure
14., page 26
) begins during State 1 of the machine
cycle, when the opcode is latched into the Instruc-
tion Register. A second retrieve occurs during S4
of the same machine cycle. Execution is complete
at the end of State 6 of this machine cycle.
The MOVX instructions take two machine cycles
to execute. No program retrieval is generated dur-
ing the second cycle of a MOVX instruction. This
is the only time program retrievals are skipped.
The retrieve/execute sequence for MOVX instruc-
tion is shown in
Figure 14., page 26
(d).
Table 14. Conditional Jump Instructions
Mnemonic
Operation
Addressing Modes
Dir.
Ind.
Reg.
Imm
JZ rel
Jump if A = 0
Accumulator only
JNZ rel
Jump if A
≠
0
Accumulator only
DJNZ <byte>,rel
Decrement and jump if not zero
X
X
CJNE A,<byte>,rel
Jump if A
≠
<byte>
X
X
CJNE <byte>,#data,rel
Jump if <byte>
≠
#data
X
X
相关PDF资料 |
PDF描述 |
|---|---|
| UPSD3212CV-24T6 | Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212CV-24U6 | Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| uPSD3212C | Flash Programmable System Devices with 8032 Microcontroller Core and 16Kbit SRAM(带8032微控制器内核和16Kbit SRAM的FLASH可编程系统器件) |
| uPSD3212CV | Flash Programmable System Devices with 8032 Microcontroller Core and 16Kbit SRAM(带8032微控制器内核和16Kbit SRAM的FLASH可编程系统器件) |
| uPSD3212 | Flash Programmable System Device with 8032 Microcontroller Core(嵌入高速“8032微控制器核”的Flash型可编程系统器件) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UPSD3212C | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212C-24T1T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core and 16Kbit SRAM |
| UPSD3212C-24T6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212C-24U1T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core and 16Kbit SRAM |
| UPSD3212C-24U6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
发布紧急采购，3分钟左右您将得到回复。