收藏本站
参数资料
型号： UPSD3212CV-24T6
厂商： 意法半导体
英文描述： Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic
中文描述： 闪存可编程系统设备与8032具有USB和可编程逻辑控制器
文件页数： 58/163页
文件大小： 2844K
代理商： UPSD3212CV-24T6
uPSD3212A, uPSD3212C, uPSD3212CV
58/163
Baud Rates.
The baud rate in Mode 0 is fixed:
Mode 0 Baud Rate = f
OSC
/ 12
The baud rate in Mode 2 depends on the value of
Bit SMOD = 0 (which is the value on reset), the
baud rate is 1/64 the oscillator frequency. If SMOD
= 1, the baud rate is 1/32 the oscillator frequency.
Mode 2 Baud Rate = (2
SMOD
/ 64) x f
OSC
In the uPSD321x Devices, the baud rates in
Modes 1 and 3 are determined by the Timer 1
overflow rate.
Using Timer 1 to Generate Baud Rates.
When
Timer 1 is used as the baud rate generator, the
baud rates in Modes 1 and 3 are determined by
the Timer 1 overflow rate and the value of SMOD
as follows (see
Table 45., page 59
):
Mode 1,3 Baud Rate =
(2
SMOD
/ 32) x (Timer 1 overflow rate)
The Timer 1 Interrupt should be disabled in this
application. The Timer itself can be configured for
either “timer” or “counter” operation, and in any of
its 3 running modes. In the most typical applica-
tions, it is configured for “timer” operation, in the
Auto-reload Mode (high nibble of TMOD = 0010B).
In that case the baud rate is given by the formula:
Mode 1,3 Baud Rate =
(2
SMOD
/ 32) x (f
OSC
/ (12 x [256 – (TH1)]))
One can achieve very low baud rates with Timer 1
by leaving the Timer 1 Interrupt enabled, and con-
figuring the Timer to run as a 16-bit timer (high nib-
ble of TMOD = 0001B), and using the Timer 1
Interrupt to do a 16-bit software reload.
Figure
22., page 50
lists various commonly used baud
rates and how they can be obtained from Timer 1.
Using Timer/Counter 2 to Generate Baud
Rates.
In the uPSD321x Devices, Timer 2 select-
ed as the baud rate generator by setting TCLK
and/or RCLK (see
Figure 22., page 50
Timer/
Counter 2 Control Register (T2CON)).
Note:
The baud rate for transmit and receive can
be simultaneously different. Setting RCLK and/or
TCLK puts Timer into its Baud Rate Generator
Mode.
The RCLK and TCLK Bits in the T2CON register
configure UART 1. The RCLK1 and TCLK1 Bits in
the PCON register configure UART 2.
The Baud Rate Generator Mode is similar to the
Auto-reload Mode, in that a roll over in TH2 causes
the Timer 2 registers to be reloaded with the 16-bit
value in registers RCAP2H and RCAP2L, which
are preset by software.
Now, the baud rates in Modes 1 and 3 are deter-
mined at Timer 2’s overflow rate as follows:
Mode 1,3 Baud Rate = Timer 2 Overflow Rate / 16
The timer can be configured for either “timer” or
“counter” operation. In the most typical applica-
tions, it is configured for “timer” operation (C/T2 =
0). “Timer” operation is a little different for Timer 2
when it’s being used as a baud rate generator.
Normally, as a timer it would increment every ma-
chine cycle (thus at the 1/6 the CPU clock frequen-
cy). In the case, the baud rate is given by the
formula:
Mode 1,3 Baud Rate = f
OSC
/ (32 x [65536 -
(RCAP2H, RCAP2L)]
where (RCAP2H, RCAP2L) is the content of
RC2H and RC2L taken as a 16-bit unsigned inte-
ger.
Timer 2 also be used as the Baud Rate Generating
Mode. This mode is valid only if RCLK + TCLK = 1
in T2CON or in PCON.
Note:
A roll-over in TH2 does not set TF2, and will
not generate an interrupt. Therefore, the Timer in-
terrupt does not have to be disabled when Timer 2
is in the Baud Rate Generator Mode.
Note:
If EXEN2 is set, a 1-to-0 transition in T2EX
will set EXF2 but will not cause a reload from
(RCAP2H, RCAP2L) to (TH2, TL2). Thus when
Timer 2 is in use as a baud rate generator, T2EX
can be used as an extra external interrupt, if de-
sired.
It should be noted that when Timer 2 is running
(TR2 = 1) in “timer” function in the Baud Rate Gen-
erator Mode, one should not try to READ or
WRITE TH2 or TL2. Under these conditions the
timer is being incremented every state time, and
the results of a READ or WRITE may not be accu-
rate. The RC registers may be read, but should not
be written to, because a WRITE might overlap a
reload and cause WRITE and/or reload errors.
Turn the timer off (clear TR2) before accessing the
Timer 2 or RC registers, in this case.
相关PDF资料
PDF描述
UPSD3212CV-24U6 Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic
uPSD3212C Flash Programmable System Devices with 8032 Microcontroller Core and 16Kbit SRAM(带8032微控制器内核和16Kbit SRAM的FLASH可编程系统器件)
uPSD3212CV Flash Programmable System Devices with 8032 Microcontroller Core and 16Kbit SRAM(带8032微控制器内核和16Kbit SRAM的FLASH可编程系统器件)
uPSD3212 Flash Programmable System Device with 8032 Microcontroller Core(嵌入高速“8032微控制器核”的Flash型可编程系统器件)
UPSD3215A-24T1 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
相关代理商/技术参数
参数描述
UPSD3212CV-24T6T 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic
UPSD3212CV-24U1T 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core and 16Kbit SRAM
UPSD3212CV-24U6 功能描述:8位微控制器 -MCU 3.0V 512K 24MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
UPSD3212CV-24U6T 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic
UPSD3212CV-40T1T 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core and 16Kbit SRAM
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*