参数资料
型号: US4881LUA-AAA-000-BU
厂商: Melexis Technologies NV
文件页数: 21/46页
文件大小: 498K
描述: IC LATCH CMOS H-S TO-92UA
产品目录绘图: UA-92 Series Side
标准包装: 1,000
传感范围: 6mT 跳闸,-6mT 释放
类型: 双极卡锁
电源电压: 2.2 V ~ 18 V
电流 - 电源: 5mA
电流 - 输出(最大): 50mA
输出类型: 数字式,开漏极
工作温度: -40°C ~ 150°C
封装/外壳: TO-226-3,TO-92-3 短体
供应商设备封装: TO-92UA
包装: 散装
产品目录页面: 2792 (CN2011-ZH PDF)
其它名称: US4881LUA
US4881LUA-ND
3-29
Cost
Hall IC cost will vary depending on the temperature specifications of BOP, BRP and Bhys. A loosely
specified device may easily be one half to one third the cost of a tightly specified device, yet perform the
same job. By providing steep slopes of flux density vs. distance and using strong magnets, the Hall IC
cost may be reduced.
Temperature Range
Hall Effect Sensors are categorized into different temperature ranges for the use in application-specific
design. It is very important that the Hall IC you select complies with your systems ambient temperature.
Position Tolerance
Depending on the application and how it is assembled, the position of components, such as the magnet,
Hall IC and mechanical assembly, will determine the mechanical variations of the system. Some systems
are more tolerant of changes in air gap and lateral motion than others.
Position Switching Accuracy
The requirement in angular (degree) or linear position ultimately governs the magnetic circuit and Hall
IC specifications. That is if switching must repeat
+
0.1250in. or
+
0.1mm then the Hall IC specification
will be much tighter than if the specification is
+
1.00 or
+
1.0mm.
Tolerance Buildup
Tolerance buildup is the sum of all the variables that determine the operate point and release point of a
Hall IC. These variables include position tolerance,temperature coefficient, wear and aging of the assem-
bly and magnet variations.
Total Effective Air Gap
As mentioned previously, both Magnet A and Magnet B in the design Kit are composed of the same mate-
rial. Although the two magnets have similar characteristics, due to the difference in size and shape
total Effective Air Gap (TEAG) will have different effects on each magnets flux density vs. distance
curve.
TEAG is defined as the sum of active area depth and the distance between the Hall ICs branded face to
the surface of the magnet. TEAG = Air Gap + Active Area Depth. Active area depth is simply the dis-
tance from the branded face of the sensor to the actual Hall Cell within it. The TEAG should be as small
as the physical system will allow, after taking into consideration factors such as the change in air gap with
temperature due to mounting, vane or interrupt thickness and wear on mounting brackets.
Graph 2 is given to show the effects of air gap on the slope of a graph using a single-pole slide-by con-
figuration with magnet A.
Section 3 - Applications
相关PDF资料
PDF描述
DOC052V-010.0M OSC OCVCXO 10.0 MHZ 3.3V SMT
AH337-PL-B IC HALL SWITCH 1PH 25MA SIP-3L
AH373-PL-B IC HALL EFFECT LATCH 25MA SIP-3L
AH3761-PG-B SENSOR HALL LATCH 6MA SIP3
F1892CCH1200 MODULE SCR/DIODE 90A 480VAC
相关代理商/技术参数
参数描述
US-4AI 制造商:Tripp Lite 功能描述:4 PORT USB DEVICE SERVER - INT - Bulk 制造商:Tripp Lite 功能描述:4 Port USB Device Server - Int
US4KB80-7000 功能描述:整流器 4.0 Amp 800 Volt RoHS:否 制造商:Vishay Semiconductors 产品:Standard Recovery Rectifiers 配置: 反向电压:100 V 正向电压下降: 恢复时间:1.2 us 正向连续电流:2 A 最大浪涌电流:35 A 反向电流 IR:5 uA 安装风格:SMD/SMT 封装 / 箱体:DO-221AC 封装:Reel
US4KB80R 功能描述:桥式整流器 Diode-Bridge Rectifier RoHS:否 制造商:Vishay 产品:Single Phase Bridge 峰值反向电压:1000 V 最大 RMS 反向电压: 正向连续电流:4.5 A 最大浪涌电流:450 A 正向电压下降:1 V 最大反向漏泄电流:10 uA 功率耗散: 最大工作温度:+ 150 C 长度:30.3 mm 宽度:4.1 mm 高度:20.3 mm 安装风格:Through Hole 封装 / 箱体:SIP-4 封装:Tube
US4KB80R-7000 功能描述:桥式整流器 4.0 Amp 800 Volt RoHS:否 制造商:Vishay 产品:Single Phase Bridge 峰值反向电压:1000 V 最大 RMS 反向电压: 正向连续电流:4.5 A 最大浪涌电流:450 A 正向电压下降:1 V 最大反向漏泄电流:10 uA 功率耗散: 最大工作温度:+ 150 C 长度:30.3 mm 宽度:4.1 mm 高度:20.3 mm 安装风格:Through Hole 封装 / 箱体:SIP-4 封装:Tube
US4PBC-E3/86A 制造商:Vishay Semiconductors 功能描述:4A,200V SM ULTRAFAST RECTIFIER - Tape and Reel