参数资料
| 型号： | USB-SPI-DIL |
| 厂商： | Flexipanel |
| 文件页数： | 8/9页 |
| 文件大小： | 0K |
| 描述： | IC USB SYNC SRL SPI 28-DIL |
| 标准包装： | 25 |
| 应用： | USB 主机/外围设备控制器 |
| 接口： | SPI 串行 |
| 电源电压： | 1.8 V ~ 5 V |
| 封装/外壳： | 28-DIP |
| 供应商设备封装： | 28-DIL |
| 包装： | 散装 |
| 安装类型： | 通孔 |
| 产品目录页面： | 659 (CN2011-ZH PDF) |
| 其它名称： | 658-1034-5 |
p8 of 9
26-Aug-10
USB-SPI
HW144-7
www.hexwax.com
Example:
94
Command – Get Firmware ID
94 55 53 42 2D 53 50 49 20 30 31 2E 30 30 00
(“USB-SPI 01.00”)
Customization
The product can be customized in one of three ways:
1. Using the HIDconfig.exe application (figure 8) in the
development kit.
This application makes it very
easy to copy the configuration from an existing
product to a new product and is suitable for in-
factory use. (It cannot be used if you have changed
the Vendor ID and / Product ID.)
2. By requesting the custom settings to be supplied
pre-programmed when buying pre-programmed
chips (5K units minimum).
3. Using customization commands.
Documentation
on these commands is available on request.
Figure 8. HIDconfig.exe application
Delivery and Programming
USB-SPI is available pre-programmed in 28-pin DIL and
20-pin SSOP packages. USB-SPI-SS (SSOP package)
may be supplied with an ID label, or it may be identified
with a green mark on the package.
In high volumes (5K+), USB-SPI is available reeled with
your custom settings preloaded, in any available
package.
TEAclipper Programming
If practical, a TEAclipper programming socket should be
added to the circuit board in order to facilitate in-circuit
firmware updates.
During programming, these connections must be
protected against contention. In particular, note that
Vpp is subject to 13V during programming. Nothing else
should be connected to Vpp except via a 22k pull-up
resistor.
The TEAclipper connector format is shown in figure 9.
Since the programming time is fast, no programming
socket is required.
The TEAclipper can be ‘leaned’
against the plate-through holes shown.
It is strongly recommended that this connector is
included in circuits even if in-circuit programming is not
anticipated, since this allows you to upgrade the
firmware if necessary.
1mm hole dia
2.54mm spacing
Pin 1 indicated
by square pad
P
G
D
P
G
C
V
pp
V
ss
V
dd
Figure 9. Recommended plate-through connector design
Evaluation Board
USB-SPI may be evaluated with the Firmware Factory
USB Products Eval Board (figure 10). The components
which must be fitted are shown in table 9. In addition,
the following connections must be made:
- Jumper A to Jumper B.
- Jumper C to Jumper D.
- Active low LED to pin 3 (RA1) of U7.
- Active high pushbutton to pin 4 (RA2) of U7.
- Pin VIO9/Send to Vdd.
- Jumper J to Jumper K (20 pin device only)
- Jumper L to Jumper M (20 pin device only)
The prototyping area on the left of the board may be
used to add the LED and pushbutton. In figure 11, an
active low LED has been connected to the AllSysGo#
pin and active high LEDs to the Tx and Rx indicators,
and a jumper provided on the Send input.
(Some
connections are on the underside of the board.)
The printed circuit board integrates an edge connector
of USB Type A format. This may be plugged into a USB
extension cable.
Table 9. Evaluation Board bill of materials
Label
Component
U2
USB-SPI-DIL
U7
PIC18F2321
D2
Wire link
C4d, C6
100nF capacitor
C7
10uF capacitor
C8
470nF capacitor
C2, C3
22pF capacitor
X1
12MHz parallel cut crystal
R2, R3
22k resistor
The PIC18F2331 serves as an SPI master for the
evaluation. When the pushbutton is pressed, the LED
lights and eight bytes are exchanged with USB-SPI.
The first time the button is pressed, the bytes 12 34 56
78 9A BC DE F0 are sent. Thereafter, the previously
received eight bytes are echoed back. The source code
for the SPI host is in the development kit.
相关PDF资料 |
PDF描述 |
|---|---|
| USB2SERA10CFK | USB TO SERIAL BRIDGE |
| V62/11608-01XE | IC SWITCH SPDT SGL 8PIN |
| VNC2-64Q1B-TRAY | IC USB HOST/DEVICE CTRL 64-QFN |
| W78E858A40FL | IC MCU 8-BIT 32K FLASH 44-PQFP |
| W83303AG | IC ACPI CONTROLLER 48-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| USB-SPI-SS | 功能描述:USB 接口集成电路 Driver-free USB to serl SPIslve intrfce RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| USBSPYDER08 | 功能描述:开发板和工具包 - 其他处理器 8-bit MCU USB Dev Kit RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
| USB-SWD/UART-CONVZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) |
| USB-T0S3 | 制造商:TELEDYNE 制造商全称:TELEDYNE 功能描述:SuperSpeed USB Analyzer |
| USBT1T11ABQX | 制造商:Fairchild Semiconductor Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。