- 您现在的位置：买卖IC网 > PDF目录11739 > USB-SPI-SS (Flexipanel)IC USB SYNC SRL SPI 20-SSOP PDF资料下载
参数资料
| 型号： | USB-SPI-SS |
| 厂商： | Flexipanel |
| 文件页数： | 2/9页 |
| 文件大小： | 0K |
| 描述： | IC USB SYNC SRL SPI 20-SSOP |
| 标准包装： | 25 |
| 应用： | USB 主机/外围设备控制器 |
| 接口： | SPI 串行 |
| 电源电压： | 1.8 V ~ 5 V |
| 封装/外壳： | 20-SSOP |
| 供应商设备封装： | 20-SSOP |
| 包装： | 散装 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 659 (CN2011-ZH PDF) |
| 其它名称： | 658-1035-5 |
p2 of 9
26-Aug-10
USB-SPI
HW144-7
www.hexwax.com
Basic Operation
To the electronic system (‘device’), USB-SPI looks like a
SPI serial slave device. To the PC (‘host’), it looks like a
Human Interface Device (HID) with which it may
exchange information using simple commands.
Using the HID USB profile means that no driver
installation is required and immediate compatibility is
assured on Windows, Linux and OS systems.
Additionally, software can find the device automatically
without needing to know which virtual COM port it is
occupying.
Pin Functions
The pin functions are shown in table 2. The function of
the virtual I/O pins is reconfigurable, so their default
settings are also shown. Note that the output pins are in
a tri-state condition until ~20μs after power-on.
Table 2. Device Pinout
DIL
SSOP Name Description
1
4
VIO0
Vpp
Virtual I/O / *Reset# (in)
TEAclipper Vpp
5
VIO1
Virtual I/O / *Tx Ind (out)
6
VIO2
Virtual I/O / *Rx Ind (out)
11
7
VIO3
Virtual I/O / *Tx/Rx Ind (out)
7
8
SS#
Slave Select input (Active low)
18
9
MISO Slave serial data output
12
10
VIO4
Virtual I/O / *All-Systems-Go# (out)
22
11
SCK
Slave serial data clock input
13
12
VIO5
Virtual I/O / *Suspend# (out)
21
13
MOSI Slave serial data input
17
14
VIO8
Virtual I/O / *Tx Buffer Empty (out)
23
15
VIO9
Virtual I/O / *Send (int)
24
16
VIO10 Virtual I/O / *Rx Buffer Not Full (out)
14
17
Vusb
USB supply filter
15
D-
USB data -
27
18
PGC
TEAclipper PGC
16
D+
USB data+
28
19
PGD
TEAclipper PGD
8,19
20
Vss
Power ground reference
20
1
Vdd
Power positive input
9
3
OSC1 Oscillator output
10
2
OSC2 Oscillator input
* = default configuration
# = active low
The pin functions are described in detail below.
Vss, Vdd, Vusb
Vss is the power supply ground reference. Vdd should
be connected to a regulated supply, for example the
USB bus power.
Vusb should be connected, via a
470nF capacitor, to Vss. See for example C8 in figure 2.
OSC1, OSC2
OSC1 and OSC2 should be connected to a 12MHz
parallel cut crystal circuit with 22pF capacitors. It may
be replaced with a 12MHz resonator with 0.25% total
tolerance.
SCK, MOSI, MISO, SS#
SPI serial data I/O. Data is input on MOSI and output
on MISO if SS# is asserted (active low) and the SCK
input is clocked. SPI can be operated in any of modes
“A”, “B”, “C” or “D” (also known as modes “3”, “1”, “2”
and “0”, and “1,1”, “0,1”, “1,0”, “0.0”, respectively). Refer
to table 3. The maximum permitted clock rate is 1MHz.
Table 3. SPI Modes
MODE CPOL CPHA Description
A*
3
1,1
1
SCK idle high
Data changes on SCK high-to-low
Data read on SCK low-to-high
B
1
0,1
0
1
SCK idle low
Data changes on SCK low-to-high
Data read on SCK high-to-low
C
2
1,0
1
0
SCK idle high
Data changes on SCK low-to-high
Data read on SCK high-to-low
D
0
0,0
0
SCK idle low
Data changes on SCK high-to-low
Data read on SCK low-to-high
* = default configuration
Vpp, PGC, PCD
TEAclipper programming pins. Refer to the Delivery
and Programming section for details. Note that the Vpp
pin may be subject to voltages as high as 12V during
programming.
VIO pins
The VIO pin functions can be reconfigured as detailed in
the customization section. The default functions are
shown in table 2. The pins can be configured as follows.
No Function
The pin is a digital input that has no effect. To minimize
power consumption, it should be biased high or low.
This setting is available on all VIOs.
Reset
The pin is an active low reset input.
Resetting the
device effectively implements the soft detach function.
This setting is available on VIO0 only.
USB Power Sense
If the device is capable of operating while not plugged
into a USB port, a USB Power Sense input should be
provided.
This pin should indicate that a voltage is
detected on the V+ pin of the USB connector. It is used
to reduce power consumption by entering into a sleep
mode when the USB is not present, and also to ensure
that the USB engine correctly initializes when the device
is plugged in. The SPI port is not operational during
sleep. This setting must be on VIO9.
Self Power Sense
If the device is capable of operating while not plugged
into a USB port, a Self Power Sense input may be
provided. This pin should indicate when the device is
not drawing power from the USB bus and can help the
PC manage its power budget. This setting is available
on any VIO pin.
Tx Indication
Output for connecting to a transmit indication LED. It
turns on for approximately 100ms when data has been
transmitted to the host. This setting is available on any
VIO pin except VIO0.
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/20WD5JN | CONN RCPT 5POS WALL MNT W/SCKT |
| PIC32MX534F064L-I/PF | MCU PIC 64KB FLASH 100TQFP |
| CS3106A-14S-64P | CONN PLUG 4POS STRAIGHT W/PINS |
| 142-0761-801 | CONN JACK SMA 50 OHMS PC MOUNT |
| PIC32MX320F128L-80V/PT | IC MCU 32BIT 128KB FLSH 100TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| USBSPYDER08 | 功能描述:开发板和工具包 - 其他处理器 8-bit MCU USB Dev Kit RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
| USB-SWD/UART-CONVZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) |
| USB-T0S3 | 制造商:TELEDYNE 制造商全称:TELEDYNE 功能描述:SuperSpeed USB Analyzer |
| USBT1T11ABQX | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| USBT801 | 功能描述:标准LED-SMD Blue RoHS:否 制造商:Vishay Semiconductors 封装 / 箱体:0402 LED 大小:1 mm x 0.5 mm x 0.35 mm 照明颜色:Red 波长/色温:631 nm 透镜颜色/类型:Water Clear 正向电流:30 mA 正向电压:2 V 光强度:54 mcd 显示角:130 deg 系列:VLMx1500 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。