- 您现在的位置：买卖IC网 > PDF目录18420 > UT-100SI (Master Appliance Co)TOOL HEAT ULTRTRCH BUTANE SLDR PDF资料下载
参数资料
| 型号： | UT-100SI |
| 厂商： | Master Appliance Co |
| 文件页数： | 5/28页 |
| 文件大小： | 0K |
| 描述： | TOOL HEAT ULTRTRCH BUTANE SLDR |
| 标准包装： | 1 |
| 系列： | Ultratorch® |
| 类型： | 丁烷吹管，无火焰 |
| 温度范围： | 1202°F（650°C） |
| 特点： | 包括：热风枪，外壳和 3 个喷嘴 |
| 相关产品： | 70-01-01-ND - TIP, 3.3MM CHISEL FOR UT-100SI 70-01-02-ND - TIP, 1.0MM CHISEL FOR UT-100SI |
| 其它名称： | MA1024 UT-100SI-ND |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Ignition Instructions
1. Set gas control lever to 3 and move On/Off lever to “ON”. In cold conditions, move gas lever
higher, in warm, lower.
2. Push ignition button all the way down slowly, holding in down position for 3 seconds after it
clicks. You may hear a whistling sound.
3. When catalyst inside of exhaust opening glows red, slowly release button.
4. If unit did not ignite, repeat.
5. To turn off, move On/Off lever to “OFF” position until it clicks.
Temperature can be changed by adjusting gas control lever.
Use as a Soldering Iron or Heat Tool
All models come with the soldering tip pre-installed. To change tips, unscrew knurled nut,
drop out tip and drop in replacement tip.
As a heat tool, heated gas flows from the end of the
heat tip. Use the heated gas to heat, dry or shrink as
necessary. Tip temperatures can be varied by adjust-
ing the gas control lever.
As a soldering iron, heat conducts into tip. Touch tip to
work surface and apply solder. Use proper tip for type
of work being performed. Make sure hot air exhaust
points away from work surface.
To Replace Ejector
The ejector is where the
air/fuel mixture takes place.
Occasionally it may be
necessary to replace due
to clogging.
Unscrew the knurled nut and
remove the tip and tip hous-
ing. Disconnect ignition wire
by gently pulling lead wire
down and away from ignition
tube. Insert spanner wrench
into small hole in the ejec-
tor. While holding spanner
wrench stationary, loosen
locking hex nut above
ejector by using open end
wrench and turning counter
clockwise. Use spanner
wrench to remove ejector.
Replace ejector and tighten.
Mount burner by turning
clockwise onto ejector until
light tension is felt. Align insu-
lation tube in a straight line
with ignition wire. Tighten hex
nut with open end wrench
while holding ejector in place
with spanner wrench. Insert
lead wire into insulation tube.
Push ignition button to con-
firm sparking. Replace tip
and tip housing.
相关PDF资料 |
PDF描述 |
|---|---|
| B32672L1103J189 | FILM CAP 10NF 5% 600VAC MKP |
| FXO-HC730R-25 | OSC 25 MHZ 3.3V HCMOS SMD |
| B32621A3473K289 | FILM CAP 0.0470UF 10% 250V |
| FXO-HC730R-25.147 | OSC 25.147 MHZ 3.3V HCMOS SMD |
| B32521C6104J189 | FILM CAP 0.1000UF 5% 400V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UT-100SIEA | 制造商:Master Appliance Corp 功能描述:ULTRATORCH WITH ENHANCED AIR FLOW, SELF-IGNITING |
| UT-100SI-HK | 制造商:Master Appliance Corp 功能描述:ULTRATORCH, HOT KNIFE HEAT TOOL, SELF-IGNITING |
| UT-100SIK | 功能描述:KIT TOOL ULTRCH SELF-IGNITING RoHS:否 类别:工具 >> 热风枪喷枪 - 配件 系列:Ultratorch® 标准包装:1 系列:- 类型:热风枪套件 温度范围:750°F ~ 806°F（400°C ~ 430°C） 电压:230V 电流:- 功率 - 额定:210W 特点:包括：热风枪，1 个喷嘴和 2 个反射器 |
| UT-100SIP | 制造商:Master Appliance Corp 功能描述:ULTRATORCH PROFESSIONAL HEAT TOOL KIT, SELF-IGNITING 制造商:Master Appliance Corp 功能描述:BUTANE POWERED SOLDERING IRON; Kit Contents:UT100Si Ultra torch, Oxygen-free Chisel & Needle Tips, Shrink Attachment, Hot Knife, Sponge; Heat Temperature Range:+650C; Input Power:80W ;RoHS Compliant: NA 制造商:Master Appliance 功能描述:ULTRATORCH PROFESSIONAL KIT |
| UT-100SI-TC | 功能描述:KIT ULTRCH BUTANE SLDR HEAT TOOL RoHS:否 类别:工具 >> 热风枪喷枪 - 配件 系列:Ultratorch® 标准包装:1 系列:- 类型:热风枪套件 温度范围:750°F ~ 806°F（400°C ~ 430°C） 电压:230V 电流:- 功率 - 额定:210W 特点:包括：热风枪，1 个喷嘴和 2 个反射器 |
发布紧急采购，3分钟左右您将得到回复。