- 您现在的位置：买卖IC网 > PDF目录225476 > UWR-12/1250-D48ACT 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | UWR-12/1250-D48ACT |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| 文件页数： | 7/12页 |
| 文件大小： | 602K |
| 代理商： | UWR-12/1250-D48ACT |
A Series
7 - 1 5 W , S I N G L E O U T P U T D C / D C C O N V E R T E R S
4
Trimming Output Voltages
These converters have a trim capability (pin 5) that allows users to adjust the
output voltage ±5%. Adjustments to the output voltage can be accomplished
via a trim pot, Figure 2, or a single xed resistor as shown in Figures 3 and 4.
A single xed resistor can increase or decrease the output voltage depending
on its connection. Fixed resistors should have an absolute TCR less than
100ppm/°C to minimize sensitivity to changes in temperature.
A single resistor connected from the Trim (pin 5) to the +Output (pin 4), see
Figure 3, will decrease the output voltage. A resistor connected from the Trim
(pin 5) to Output Common (pin 6) will increase the output voltage.
Trim adjustment greater than 5% can have an adverse effect on the convert-
er's performance and is not recommended.
20k
5-22
Turns
+INPUT
+OUTPUT
COMMON
TRIM
–INPUT
ON/OFF
CONTROL
1
2
3
4
5
LOAD
6
+INPUT
+OUTPUT
COMMON
TRIM
–INPUT
ON/OFF
CONTROL
1
2
3
4
5
LOAD
6
RTRIM DOWN
+INPUT
+OUTPUT
COMMON
TRIM
–INPUT
ON/OFF
CONTROL
1
2
3
4
5
LOAD
6
RTRIM UP
Figure 2.Trim Connections Using A Trim Pot
Figure 4.Trim Connections To Increase Output Voltage Using Fixed Resistors
Figure 3.Trim Connections To Decrease Output Voltage Using Fixed Resistors
T E C H N I C A L
N O T E S
Floating Outputs
Since these are isolated DC/DC converters, their outputs are "oating."
Designers will usually use the output Common (pin 6) as the ground/return of
the load circuit.You can, however, use the +Output (pin 4) as ground/return to
effectively reverse the output polarity.
Minimum Output Loading Requirements
1.2 to 5V models employ a synchronous-rectier design topology. All models
regulate within spec and are stable under no-load conditions. 12/15V models
employ a traditional forward architecture and require 10% loading (125mA for
12V models, 100mA for 15V models) to achieve their listed regulation specs.
12/15V models also have a minimum-load-for-stability requirement (25mA).
For 12/15V models, operation between 25mA and 10% loading will result
in stable operation but regulation may degrade. Operation under no-load
conditions will not damage the 12/15V devices; however they may not meet
all listed specications.
Filtering and Noise Reduction
All A-Series UWR DC/DC Converters achieve their rated ripple and noise
specications using the external input and output capacitors specied in
the Performance/Functional Specications table. In critical applications, input/
output noise may be further reduced by installing additional external I/O caps.
Input capacitors should be selected for bulk capacitance, low ESR and high
rms-ripple-current ratings. Output capacitors should be selected for low ESR
and appropriate frequency response. All caps should have appropriate volt-
age ratings and be mounted 2-3 inches from the converter to achieve
published ratings.
The most effective combination of external I/O capacitors will be a function
of your particular load and layout conditions. Our Applications Engineers will
be happy to recommend potential solutions and can discuss the possibility of
our modifying a given device’s internal ltering to meet your specic require-
ments. Contact our Applications Engineering Group for additional details.
Input Fusing
Certain applications and/or safety agencies may require the installation of
fuses at the inputs of power conversion components. Fuses should also be
used if the possibility of sustained, non-current-limited, input-voltage polarity
reversals exists. For DATEL A-Series UWR 7-15 Watt DC/DC Converters, you
should use slow-blow type fuses with values no greater than the following.
VIN Range
Fuse Value
"D12A" Models
3 Amps
"D24A" Models
2 Amps
"D48A" Models
1 Amp
相关PDF资料 |
PDF描述 |
|---|---|
| UWR-2.5/6000-D48AN | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| UWR-5/3000-D48ACT | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| UWR-1.5/6000-D12AL2 | 1-OUTPUT 9 W DC-DC REG PWR SUPPLY MODULE |
| UWR-1.5/6000-D12ANL2 | 1-OUTPUT 9 W DC-DC REG PWR SUPPLY MODULE |
| UWR-1.5/6000-D24ANTL2 | 1-OUTPUT 9 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UWR-12-830-D12A-C | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:Single Output, High Reliability, 2" x 1", 6-10 Watt, DC/DC Converters |
| UWR14-20WA-SERIES | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:Single Output, High Reliability |
| UWR-15/1000-D12A | 功能描述:DC/DC转换器 15W 12Vto15V 1000mA RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| UWR-15/1000-D12AC | 功能描述:DC/DC转换器 15W 12Vto15V 1000mA RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| UWR-15/1000-D12A-C | 功能描述:DC/DC转换器 15W 12Vto15V 1000mA RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。