参数资料
型号: VE-BAMD-CM
元件分类: 电源模块
英文描述: 2-OUTPUT 600 W AC-DC PWR FACTOR CORR MODULE
封装: ROHS COMPLIANT PACKAGE-9
文件页数: 7/10页
文件大小: 662K
代理商: VE-BAMD-CM
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
HAM, Harmonic Attenuation Module
Rev. 2.1
Page 6 of 10
Set your site on VICOR at vicorpower.com
Component
Description
Vicor
Designation
Part Number
C1
0.1
μF ceramic, 50 V
C2, C3
0.01
μF ceramic, 50 V
C4
Hold up capacitor,
Available as a HUB
1000 to 6,000
μF
from Vicor (see
adjoining table)
C5–C8
4,700 pF Y2 cap.
01000
C9,C10
0.2
μF, 500 V
Film or Ceramic
D1
1N4691 zener, 6.2 V
D2, D3
1N4006 diode, 800 V
00670
D4, D5
1N5817 schottky diode, 20 V
26108
F1, F2
Use recommended fusing for specific
DC-DC Converters
F3
20 A, 250 V
R1
50 K
Ω
R4**
100 K
Ω, 2 W
V1
240 V MOV
30076
Z1, Z2
130 V Transorb
1.5KE130CA
Z3
150 V Transorb
1.5KE150CA
+IN
VI-26x or VI-J6x DC-DC Converters
GATE IN
GATE OUT
-IN
F2
+IN
F1
R1
D1
D2
D4
C2
C4
C5
C6
C7
C8
JMK Filter
P/N 1319-13
12.6 A
*
+IN
GATE IN
GATE OUT
-IN
+OUT
-OUT
P/OK
E/O
A/S
VI-HAMD-xM
GATE IN
GATE OUT
-IN
+IN
+OUT
-OUT
VI-BAMD-xM
Input
Bridge
Rectifier
Vicor P/N 30660
L1
GND
L2/N
L1
L2/N
1N4006
F3
R4
**
C1
V1
C9
C10
* Consult Vicor's Applications Engineering for specific
HAMD / BAMD filtering information.
** A 100 K
Ω, 2 W resistor is used for every 1,000 μF
of hold up capacitance.
Z1
Z2
Z3
10 A
Hold up Box (HUB)
2000
μF HUB1000-P 1200 W
GATE IN
GATE OUT
Driver
Booster (N)
Figure 5 — Connection Diagram, HAMD / BAMD / VI-26x or VI-J6x DC-DC Converters
HAMD-CM Driver HAM: No internal bridge rectifier or synchronization diodes.
BAMD-CM Booster HAM: Companion module to HAMD-CM used for additional output power. No internal bridge rectifier.
+OUT
P/OK
–OUT
E/O
A/S
18 k
Ω, 1/4 W
"Power OK" Status
Low = OK
A/S
E/O
P/OK
+OUT
–OUT
IAS ≤ 3 mA
19 – 23 V
+
DO NOT OVERLOAD
or directly connect a capacitor
to the A/S terminal.
Figure 6 — Auxiliary Supply (A/S)
A/S
The HAM provides a low voltage non isolated output Auxiliary
Supply (A/S) that may be used to power primary side control
and monitoring circuitry. This output is 19 – 23 Vdc, referenced
to -OUT, at 3 mA max. Do not overload or short this output as
the HAM will fail. A typical use for A/S is to power an optical
coupler that isolates the Power OK signal Figure 6.
E/O
The Enable Output (E/O) is used to inhibit the DC-DC
converters at start up until the hold up capacitors are charged,
at which time Enable is asserted high (open state, Figure 8).
If the AC line fails, E/O goes low when the DC output of the
HAM drops below 195 Vdc.
E/O must be connected to the Gate Input of all VI-26x and
VI-J6x drivers Figure 4; failure to do so may cause the
converters to toggle on and off. It is not necessary to connect
this pin to boosters as they are controlled by their respective
driver. If an external load is connected directly to the output
of the HAM, do not apply the load until the output hold up
capacitor(s) are fully charged.
The E/O pin ancillary circuitry illustrated in Figures 4 and 5
provides transient immunity. The illustrated circuitry is the
minimum required, see Figures 4 and 5.
PIN FUNCTION / DESCRIPTION (CONT.)
相关PDF资料
PDF描述
VE-BAMD-IMVE-BAMD-IM 2-OUTPUT 600 W AC-DC PWR FACTOR CORR MODULE
VE-BAMD-MMVE-BAMD-MM 2-OUTPUT 600 W AC-DC PWR FACTOR CORR MODULE
VE-CMUG-CM-CC 1-OUTPUT 575 W AC-DC PWR FACTOR CORR MODULE
VE-J5H-MZ-S 1-OUTPUT 25 W DC-DC REG PWR SUPPLY MODULE
VI-J0Y-CZ-S 1-OUTPUT 25 W DC-DC REG PWR SUPPLY MODULE
相关代理商/技术参数
参数描述
VE-BAMD-CML 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:High-Boost Harmonic Attenuation Module
VE-BAND-CL 制造商:POWERBOX 制造商全称:Powerbox 功能描述:AC INPUT HARMONIC ATTENUATOR MODULE
VE-BAND-CM 制造商:POWERBOX 制造商全称:Powerbox 功能描述:AC INPUT HARMONIC ATTENUATOR MODULE
VE-BAND-EL 制造商:POWERBOX 制造商全称:Powerbox 功能描述:AC INPUT HARMONIC ATTENUATOR MODULE
VE-BAND-EM 制造商:POWERBOX 制造商全称:Powerbox 功能描述:AC INPUT HARMONIC ATTENUATOR MODULE