参数资料
型号: VK204-25
厂商: Matrix Orbital
文件页数: 14/47页
文件大小: 2507K
描述: VFD ALPHA/NUM DISPL 20X4 SER
产品变化通告: VK204-25 Series Release 03/Mar/2010
12C Displays Change 11/Oct/2011
产品目录绘图: LCD, VFD and PLED Display
标准包装: 1
系列: VK204-25
外形L x W x H: 98.00mm x 61.00m x 24.40mm
可视范围: 70.80mm L x 20.90mm W
显示格式: 20 x 4
显示器类型: 字符
格式: 5 x 7 点
字符尺寸: 4.70mm H x 2.40mm W
接口: 串行
工作温度: -20°C ~ 70°C
产品目录页面: 2846 (CN2011-ZH PDF)
相关产品: VFD-GREEN-204-ND - LCD ACCY VFD FILTER 20X4 GREEN
VFD-RED-204-ND - LCD ACCY VFD FILTER 20X4 RED
VFD-GREY-204-ND - LCD ACCY VFD FILTER 20X4 GRAY
VFD-BLUE-204-ND - LCD ACCY VFD FILTER 20X4 BLUE
其它名称: 635-1026
21
Communication
When communication of either text or commands is interrupted, try the steps below.
?
First, check the communication cable for continuity. If you don't have an ohm meter, try using a
different communication cable. If you are using a PC try using a different Com Port.
?
Next, please ensure that the display module is set to communicate on the protocol that you are
using, by checking the Protocol Select Jumpers.
?
In serial protocol, ensure that the host system and display module are both communicating on
the same baud rate. The default baud rate for the display module is 19200 bps.
?
Match Rx from the LVK204-25
to the transmitting pin from your host and the Tx pin to the
receiving pin.
?
If you are communicating to the display via I2C*
please ensure that the data is being sent to the
correct address. The default slave address for the display module is 80.
?
In I2C mode, connect Rx to the data line of your controller and Tx to the data output.
?
Unlock the display. See the Set and Save Data Lock command for more info.
?
Finally, you may reset the display to its default settings using the Manual Override procedure
outlined below.
*Note:
I2C communication will always require pull up resistors
on SCL and SDA of one to ten kilohms.
Manual Override
Should the settings of your display
become altered in a way that dramatically
impacts usability, the
default settings
can be temporarily restored. To override the display, please follow the steps below.
1.
Disconnect power from your display.
2.
Place a jumper on the middle two pins of the keypad header, R5 and C1.
3.
Reconnect power to your unit, and wait for the start screen before removing the override
jumper.
4.
Settings will be temporarily**
overridden to the defaults listed in the Manual Override Settings
table. At this point any important settings, such as contrast, backlight, or baud rate, should not
only be set but saved so they remain when the override is removed.
Parameter
Value
Backlight
255
Contrast
128
Baud Rate
19200
I2C Address
80
Table 19: Manual Override Settings
**Note:
The display module will revert back to the old settings once turned off, unless desired settings are saved.
相关PDF资料
PDF描述
VK202-25-USB 2X20 VFD DISPLAY USB BLU/GRN
SS-5GL-F SWITCH BASIC SPDT 5A
SCK-128X8T-N026 STAR BRIGHT VFD DISPLAY BLUE
CU200211-Y1A VACUUM FLUORESCENT DISPLAY
V-161-C5R SWITCH HINGE LEVER SPDT 16A
相关代理商/技术参数
参数描述
VK204-25-422 功能描述:真空荧光显示器 - VFD 20x4 Grn Txt Blk B/G No Backlight 25 key RoHS:否 制造商:Noritake 产品:Graphic Display Modules 字符计数 x 行: 模块大小 - 宽x高x厚:230 mm x 78 mm x 15 mm 观察区域 - 宽x高:166.25 mm x 41.45 mm 接口: 电压额定值:5 V 工作温度范围:- 40 C to + 85 C 封装:
VK204-25-422-E 功能描述:真空荧光显示器 - VFD 20x4Grn Txt Blk B/G No B/L Ext. Temp RoHS:否 制造商:Noritake 产品:Graphic Display Modules 字符计数 x 行: 模块大小 - 宽x高x厚:230 mm x 78 mm x 15 mm 观察区域 - 宽x高:166.25 mm x 41.45 mm 接口: 电压额定值:5 V 工作温度范围:- 40 C to + 85 C 封装:
VK204-25-422-V 功能描述:真空荧光显示器 - VFD 20x4 Grn Txt Blk B/G No B/L Ext. Volt RoHS:否 制造商:Noritake 产品:Graphic Display Modules 字符计数 x 行: 模块大小 - 宽x高x厚:230 mm x 78 mm x 15 mm 观察区域 - 宽x高:166.25 mm x 41.45 mm 接口: 电压额定值:5 V 工作温度范围:- 40 C to + 85 C 封装:
VK204-25-422-VPT 功能描述:真空荧光显示器 - VFD 20x4 Grn Txt Blk B/G No B/L Volt Reg RoHS:否 制造商:Noritake 产品:Graphic Display Modules 字符计数 x 行: 模块大小 - 宽x高x厚:230 mm x 78 mm x 15 mm 观察区域 - 宽x高:166.25 mm x 41.45 mm 接口: 电压额定值:5 V 工作温度范围:- 40 C to + 85 C 封装:
VK204-25-422-VPT-E 制造商:Matrix Orbital 功能描述:20x4 VFD,RS422,25key Wide Volt, Ext Temp