- 您现在的位置：买卖IC网 > PDF目录16654 > VPB-5/8-0-SP (TE Connectivity)HEAT SHRINK TUBING PDF资料下载
参数资料
| 型号： | VPB-5/8-0-SP |
| 厂商： | TE Connectivity |
| 文件页数： | 3/8页 |
| 文件大小： | 0K |
| 描述： | HEAT SHRINK TUBING |
| 标准包装： | 200 |
| 系列： | VPB |
| 类型： | 套管，弹性 |
| 收缩比率： | 2 至 1 |
| 内径 - 提供： | 0.626"（15.9mm） |
| 内径 - 恢复： | 0.315"（8.0mm） |
| 已恢复的墙壁厚度： | 0.042"（1.07mm） |
| 材质： | 氟橡胶 |
| 特点： | 阻燃 |
| 颜色： | 黑 |
| 其它名称： | 5580654002 |
SPECIFICATION RT-1148 ISSUE 8
Page 3
4.3.1
Dimensions and Longitudinal Change
Measure three 6 inch (152 mm) specimens of tubing, as supplied, for length ± 1/32 inch
(± 1 mm) and inside diameter in accordance with ASTM D 2671. Condition these
specimens for 10 minutes in a 200 ± 5°C (392 ± 9°F) oven or equivalent, cool to 23 ±
3°C (73 ± 5°F) and then remeasure. Calculate longitudinal change as follows:
C =
L1 - L0
L0
x 100
Where:
C
L0
L1
=
=
=
Longitudinal Change [Percent]
Length Before Conditioning [inches (mm)]
Length After Conditioning [inches (mm)]
4.3.2
4.3.3
4.3.4
Tensile Strength, Tensile Stress and Elongation
Test three specimens of tubing for tensile strength, tensile stress and elongation in
accordance with ASTM D 2671. For tubing sizes 3/8 and smaller, the specimens shall be
full sections of tubing; for sizes 1/2 and larger, the specimens shall be cut with die D of
ASTM D 412. The specimens shall have1 inch (25 mm) bench marks centrally located.
The testing machine shall have an initial jaw separation of 1 inch (25 mm) for full
sections of tubing and 2 inches (51 mm) for die-cut specimens. The rate of jaw separation
shall be 20 ± 2 inches (508 ± 50 mm) per minute.
Low Temperature Flexibility
Condition three specimens, each 12 inches (300 mm) in length and a mandrel selected in
accordance with Table 2, at -65 ± 5°C (-85 ± 9°F) for 4 hours. For tubing sizes 3/4 or
less, the specimens shall be whole sections of tubing recovered on a stranded wire
(nearest AWG which is larger than the sleeving maximum inside diameter after
unrestricted shrinkage). For tubing sizes larger than 3/4, the specimens shall be 1/4-inch
(6.3 mm) wide strips cut from tubing which has been recovered in accordance with 4.3.1.
After 4 hours conditioning and while still at the conditioning temperature, wrap the
specimens around the mandrel for not less than 360 degrees in 10 ± 2 seconds then
visually examine the specimens for evidence of cracking.
Heat Shock
Three 6 inch (152 mm) specimens of tubing shall be conditioned for 4 hours in a 225 ±
5°C (437 ± 9°F) oven. After conditioning, remove the specimens from the oven, cool to
room temperature and bend through 180 degrees in 2 to 4 seconds over a mandrel
selected in accordance with Table 2. Visually examine the specimens for evidence of
dripping, flowing or cracking. Any side-cracking caused by flattening of the specimen on
the mandrel shall not constitute failure.
If this document is printed it becomes uncontrolled. Check for the latest revision.
? 2005 Tyco Electronics Corporation. All rights reserved
相关PDF资料 |
PDF描述 |
|---|---|
| ESA10DRST-S288 | CONN EDGECARD 20POS .125 EXTEND |
| CB5124-000 | HEAT SHRINK TUBING |
| H4PXS-4018M | DIP CABLE - HDP40S/AE40M/X |
| GMC08DRTF | CONN EDGECARD 16POS DIP .100 SLD |
| ELC-16B390L | COIL CHOKE 39UH RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| VPB-7/8-0-SP | 功能描述:HEAT SHRINK TUBING RoHS:是 类别:线缆，导线 - 管理 >> 热缩管 系列:VPB MSDS 材料安全数据表:HSTT,HSTTA,HSTTV, HSTTVA Series MSDS 标准包装:1 系列:HSTT 类型:套管，弹性 收缩比率:2 至 1 长度:100.0'（30.5m） 内径 - 提供:1.000"（25.4mm） 内径 - 恢复:0.500"（12.7mm） 已恢复的墙壁厚度:0.035"（0.89mm） 材质:聚烯烃 特点:阻燃 颜色:蓝 相关产品:HSG-115V-650-ND - TOOL GUN HEAT SHRINK HI TEMP 10A |
| VPB-7/8-0SPCS5444 | 制造商:TE Connectivity 功能描述:VPB-7/8-0SPCS5444 |
| VPB-7/8-0-SP-CS7278 | 制造商:TE Connectivity 功能描述:VPB-7/8-0-SP-CS7278 |
| VPB-7/8-0-SP-CS7733 | 制造商:TE Connectivity 功能描述:CM6832-000 |
| VPB7029036EG000050 | 制造商:PLETRONICS 制造商全称:Pletronics, Inc. 功能描述:3.3 V PECL VCXO Oscillators |
发布紧急采购，3分钟左右您将得到回复。