- 您现在的位置：买卖IC网 > Datasheet目录368 > W19B320ATT7H (Winbond Electronics)IC FLASH 32MBIT 70NS 48TSOP Datasheet资料下载
参数资料
| 型号： | W19B320ATT7H |
| 厂商： | Winbond Electronics |
| 文件页数： | 10/53页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 32MBIT 70NS 48TSOP |
| 标准包装： | 96 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 32M（4M x 8，2M x 16） |
| 速度： | 70ns |
| 接口： | 并联 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -20°C ~ 85°C |
| 封装/外壳： | 48-TFSOP（0.724"，18.40mm 宽） |
| 供应商设备封装： | 48-TSOP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页
W19B320AT/B
6.1.11 Write Protect (#WP)
The Write Protect function provides a hardware method to protect the certain boot sectors without
using V ID . This function is one of two features provided by the #WP/ACC pin.
When the #WP/ACC pin is set at V IL , the device disables program and erase functions in the two
outermost 8 Kbytes boot sectors independently of whether those sectors were protected or
unprotected using the method described in “Sector/Sector Block Protection and Unprotection.” The
two outermost 8 Kbytes boot sectors are the two sectors containing either the lowest addresses in a
bottom-boot-configured device or the highest addresses in a top-boot-configured device.
When the #WP/ACC pin is set at V IH , the device reverts to the two outermost 8 Kbytes boot sectors
were last set either to be protected or unprotected. That is, sector Protection or Unprotection for these
two sectors depends on whether they were last protected or unprotected using the method described
in “Sector/Sector Block Protection and Unprotection”.
Please note that the #WP/ACC pin must not be left floating or unconnected; otherwise, the
inconsistent behavior of the device may occur.
6.1.12 Temporary Sector Unprotect
This feature allows temporary Unprotection of previously protected sectors to change data in-system.
When the #RESET pin is set to V ID , the Sector Unprotect mode is activated. During this mode,
formerly protected sectors can be programmed or erased by selecting the sector addresses. What if
V ID is removed from the #RESET pin, all the previously protected sectors are protected again.
6.1.13 Security Sector Flash Memory Region
The Security Sector feature provides an OTP memory region that enables permanent device
identification through an Electronic Serial Number (ESN). The Security Sector uses a Security Sector
Indicator Bit (DQ7) to indicate whether the Security Sector is locked or not when shipped from the
factory. The DQ7 is permanently set when it is in the factory and cannot be changed, which prevents
copying of a factory locked part. This ensures the security of the ESN when the product is shipped to
the field. This issue should be considered during system design. Winbond offers the device with the
Security Sector either factory locked or customer lockable. The factory-locked version is always
protected when shipped from the factory, and has the Security Sector Indicator Bit permanently set to
“1” The customer-lockable version is shipped with the Security Sector unprotected, which allowing
customers to utilize the sector in any ways they choose. The customer-lockable version has the
Security Sector Indicator Bit permanently set to “0.” Thus, the Security Sector Indicator Bit prevents
customer-lockable devices from being used to replace devices that are factory locked.
The system accesses the Security Sector through a command sequence (see “Enter Security
Sector/Exit Security Sector Command Sequence”). After the system has written the Enter Security
Sector command sequence, it may read the Security Sector by using the addresses normally
occupied by the boot sectors. This mode of operation continues until the system issues the Exit
Security Sector command sequence, or until power is removed from the device. On power-up, or
following a hardware reset, the device reverts to sending commands to the boot sectors.
Factory Locked: Security Sector Programmed and Protected At the Factory
The device Security Sector is protected when it is shipped from the factory, and it cannot be modified
in any way. The device is available to be preprogrammed by one of the following:
?
?
?
A random, secure ESN only
Customer code through the supplier's service
Both a random, secure ESN and customer code through supplier's service.
- 10 -
相关PDF资料 |
PDF描述 |
|---|---|
| W19B320BTT7H | IC FLASH 32MBIT 70NS 48TSOP |
| W25Q128BVEIG | IC SPI FLASH 128MBIT 8WSON |
| W25Q16BVSFIG | IC SPI FLASH 16MBIT 16SOIC |
| W25Q16CVSFIG | IC SPI FLASH 16MBIT 16SOIC |
| W25Q16DWSFIG | IC FLASH SPI 16MBIT 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W19B320B | 制造商:WINBOND 制造商全称:Winbond 功能描述:32Mbit, 2.7~3.6-volt single bank CMOS flash memory |
| W19B320BB | 制造商:WINBOND 制造商全称:Winbond 功能描述:32Mbit, 2.7~3.6-volt single bank CMOS flash memory |
| W19B320BB-H | 制造商:WINBOND 制造商全称:Winbond 功能描述:2.7~3.6-volt write (program and erase) operations |
| W19B320BB-M | 制造商:WINBOND 制造商全称:Winbond 功能描述:2.7~3.6-volt write (program and erase) operations |
| W19B320BT | 制造商:WINBOND 制造商全称:Winbond 功能描述:32Mbit, 2.7~3.6-volt single bank CMOS flash memory |
发布紧急采购，3分钟左右您将得到回复。