- 您现在的位置：买卖IC网 > PDF目录297788 > W25X32AVSFIG (WINBOND ELECTRONICS CORP) 4M X 8 FLASH 2.7V PROM, PDSO16 PDF资料下载
参数资料
| 型号： | W25X32AVSFIG |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 4M X 8 FLASH 2.7V PROM, PDSO16 |
| 封装： | 0.300 INCH, GREEN, PLASTIC, SOIC-16 |
| 文件页数： | 2/45页 |
| 文件大小： | 1308K |
| 代理商： | W25X32AVSFIG |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
W25X32A
- 10 -
9.2 WRITE PROTECTION
Applications that use non-volatile memory must take into consideration the possibility of noise and other
adverse system conditions that may compromise data integrity. To address this concern the W25X32A
provides several means to protect data from inadvertent writes.
9.2.1
Write Protect Features
Device resets when VCC is below threshold.
Time delay write disable after Power-up.
Write enable/disable instructions.
Automatic write disable after program and erase.
Software write protection using Status Register.
Hardware write protection using Status Register and /WP pin.
Write Protection using Power-down instruction.
Upon power-up or at power-down the W25X32A will maintain a reset condition while VCC is below the
threshold value of VWI, (See Power-up Timing and Voltage Levels and Figure 20). While reset, all
operations are disabled and no instructions are recognized. During power-up and after the VCC voltage
exceeds VWI, all program and erase related instructions are further disabled for a time delay of tPUW. This
includes the Write Enable, Page Program, Sector Erase, Block Erase, Chip Erase and the Write Status
Register instructions. Note that the chip select pin (/CS) must track the VCC supply level at power-up until
the VCC-min level and tVSL time delay is reached. If needed a pull-up resister on /CS can be used to
accomplish this.
After power-up the device is automatically placed in a write-disabled state with the Status Register Write
Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Page Program, Sector
Erase, Chip Erase or Write Status Register instruction will be accepted. After completing a program,
erase or write instruction the Write Enable Latch (WEL) is automatically cleared to a write-disabled state
of 0.
Software controlled write protection is facilitated using the Write Status Register instruction and setting
the Status Register Protect (SRP) and Block Protect (TB, BP2, BP1, and BP0) bits. These Status
Register bits allow a portion or all of the memory to be configured as read only. Used in conjunction with
the Write Protect (/WP) pin, changes to the Status Register can be enabled or disabled under hardware
control. See Status Register for further information.
Additionally, the Power-down instruction offers an extra level of write protection as all instructions are
ignored except for the Release Power-down instruction.
相关PDF资料 |
PDF描述 |
|---|---|
| W26L04AJ-12I | 256K X 16 STANDARD SRAM, 12 ns, PDSO44 |
| W26L04AH-10 | 256K X 16 STANDARD SRAM, 10 ns, PDSO44 |
| W28A | CERPAC, 28 LEAD |
| W2H11A1018AT | 1 FUNCTIONS, 100 V, 0.5 A, FEED THROUGH CAPACITOR |
| W3DG6418V10D1 | 16M X 64 SYNCHRONOUS DRAM MODULE, 6 ns, ZMA144 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W25X32AVSSIG | 制造商:Winbond Electronics Corp 功能描述:Flash Serial-SPI 3.3V 32Mbit 4M x 8bit 7ns 8-Pin SOIC W |
| W25X32AVZEIG | 制造商:WINBOND 制造商全称:Winbond 功能描述:32M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI |
| W25X32AVZPIG | 制造商:WINBOND 制造商全称:Winbond 功能描述:32M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI |
| W25X32BV | 制造商:WINBOND 制造商全称:Winbond 功能描述:32M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI |
| W25X32BVSFIG | 制造商:WINBOND 制造商全称:Winbond 功能描述:32M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI |
发布紧急采购，3分钟左右您将得到回复。