- 您现在的位置：买卖IC网 > PDF目录22241 > W25X80AVZPIG (Winbond Electronics)IC FLASH 16MBIT 100MHZ 8WSON PDF资料下载
参数资料
| 型号： | W25X80AVZPIG |
| 厂商： | Winbond Electronics |
| 文件页数： | 23/45页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 16MBIT 100MHZ 8WSON |
| 标准包装： | 100 |
| 系列： | SpiFlash® |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 8M（1M x 8） |
| 速度： | 100MHz |
| 接口： | SPI 串行 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-WDFN 裸露焊盘 |
| 供应商设备封装： | 8-WSON（6x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
W25X10A, W25X20A, W25X40A, W25X80A
10.2.11 Sector Erase (20h)
The Sector Erase instruction sets all memory within a specified sector (4K-bytes) to the erased state
of all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Sector
Erase Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS
pin low and shifting the instruction code “20h” followed a 24-bit sector address (A23-A0) (see Figure
2). The Sector Erase instruction sequence is shown in figure 12.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not
done the Sector Erase instruction will not be executed. After /CS is driven high, the self-timed Sector
Erase instruction will commence for a time duration of t SE (See AC Characteristics). While the Sector
Erase cycle is in progress, the Read Status Register instruction may still be accessed for checking the
status of the BUSY bit. The BUSY bit is a 1 during the Sector Erase cycle and becomes a 0 when the
cycle is finished and the device is ready to accept other instructions again. After the Sector Erase
cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Sector
Erase instruction will not be executed if the addressed page is protected by the Block Protect (TB,
BP2, BP1, and BP0) bits (see Status Register Memory Protection table).
Figure 12. Sector Erase Instruction Sequence Diagram
Publication Release Date: August 7, 2009
- 23 -
Revision F
相关PDF资料 |
PDF描述 |
|---|---|
| W25X80AVSSIG | IC FLASH 16MBIT 100MHZ 8SOIC |
| W25X40AVDAIZ | IC FLASH 16MBIT 100MHZ 8DIP |
| VE-J0P-CX-F1 | CONVERTER MOD DC/DC 13.8V 75W |
| W25X40AVZPIG | IC FLASH 16MBIT 100MHZ 8WSON |
| NCP500SQL18T1G | IC REG LDO 1.8V .15A 6-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W25X80L | 制造商:WINBOND 制造商全称:Winbond 功能描述:1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT 2.5V SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI |
| W25X80LDAC | 制造商:WINBOND 制造商全称:Winbond 功能描述:1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI |
| W25X80LDACG | 制造商:WINBOND 制造商全称:Winbond 功能描述:1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI |
| W25X80LDACZ | 制造商:WINBOND 制造商全称:Winbond 功能描述:1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI |
| W25X80LDAI | 制造商:WINBOND 制造商全称:Winbond 功能描述:1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI |
发布紧急采购，3分钟左右您将得到回复。