- 您现在的位置：买卖IC网 > PDF目录297790 > WL102BC (Mitel Networks Corporation) Wireless Data Controller PDF资料下载
参数资料
| 型号： | WL102BC |
| 厂商： | Mitel Networks Corporation |
| 英文描述： | Wireless Data Controller |
| 中文描述： | 无线数据控制器 |
| 文件页数： | 5/9页 |
| 文件大小： | 138K |
| 代理商： | WL102BC |
5
Advance Information
WL102
Memory Control Block
The memory Control Block allows access to the dual port
buffer used to communicate between the Host and WL102
system processes. The control logic of the buffer RAM
allows the Host to asynchronously read or write data at the
same time as the WL102 MAC system. To help arbitrate
access to this buffer space, a
hardware semaphore
system is also included.
The WL102 contains 6784 bytes of low power buffer RAM
on chip. The 144-pin package option also allows for an
external (single port) SRAM to be used to increase the
buffer RAM space, up to 64Kbytes.
Host Interface
The Host Interface has been designed to be flexible
enough to allow its use from small microprocessor systems
to PC-Card slots. In a minimum configuration it uses only
4 address locations and a standard microprocessor type
read and write cycle. The interface provides access to the
Buffer RAM, which is accessible by both the Host and the
MAC systems simultaneously, and also to a control regis-
ter which allows the Host to reset or interrupt the MAC
processor, and performs some other control functions on
the WL102.
Packets of data are typically buffered in the internal buffer
RAM before being transmitted or transferred from the MAC
system to the host.
The 8-bit interface is microprocessor and PCMCIA-com-
patible, with a separate dedicated RAM providing 255
bytes of attribute memory used for the configuration and
control of a PC Card. The host interface may be used by
any microprocessor-type interface which can supply two
bits of address, a chip enable signal, read/write strobes
and 8 bits of data, subject to timing requirements of the
WL102. The interface also provides an interrupt signalling
mechanism between the Host and MAC system as well as
some other control functions, such as a hardware sema-
phore and reset circuitry.
Communications Control Block
This block of the WL102 performs many of the functions
required for transmission and reception of data packets,
and interfaces directly to the radio transceiver. For power
sensitive applications the configuration registers can have
their clocks switched off once the initial configuration is
complete and for protocols which allow the transceiver to
sleep for periods of time, the clocks to the entire block can
be disabled via the Power Control register.
The CCB handles all the control signals for the radio and
can be configured for the timing required by the transceiver
being used. The CCB can directly access data stored in the
buffer RAM, via a DMA bus separate to the processor bus,
and once configured will finally handle a transmission or
reception, including CRC checking, address match, op-
tional data scrambling (Bias suppression encoding) and
transfer of the data to/from the buffer RAM.
For shorter network management packets the MAC
system processor can directly read/write up to 64 bytes of
data from/to the CCB FIFO. The CCB generates maskable
interrupts to the MAC system processor at defined points
in the receive/transmit process to allow the processor to
perform any additional processing required to
succcccessfully complete the receive or transmit
sequence.
The Features of the CCB include:
q
Transmission and reception of 2-level and 4-level
GFSK
bit streams at 625Kbps, 1Mbps and 2Mbps.
q
Configurable Preamble/Frame word generation
and recognition
q
Checksum generation and validation (CRC-16 and
CRC-32)
q
Optional data coding schemes: bit-stuffing,
scrambling and bias suppression encoding (as
per draft IEEE 802.11)
q
Dedicated data path for DMA transfer to and from
buffer RAM
q
Address matching on received data packet
q
Analysis of received signal for performing clear
channel assessment, including 16-bit countdown
timer
q
8 (maskable) interrupt sources to optimise
operation of the system software
q
Automatic synthesiser channel loading for Rx/Tx
when using WL600/WL800
相关PDF资料 |
PDF描述 |
|---|---|
| WL102BIG | Wireless Data Controller |
| WL102BIGTP1R | Wireless Data Controller |
| WL102BPRFP1R | Wireless Data Controller |
| WL102 | () |
| WL10 | SILICON BRIDGE RECTIFIERS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| WL102BC/PR/FP1R | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:Wireless Data Controller |
| WL102BCPRTP1R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Consumer IC |
| WL102BIG | 制造商:MITEL 制造商全称:Mitel Networks Corporation 功能描述:Wireless Data Controller |
| WL102BIGTP1R | 制造商:MITEL 制造商全称:Mitel Networks Corporation 功能描述:Wireless Data Controller |
| WL102BPRFP1R | 制造商:MITEL 制造商全称:Mitel Networks Corporation 功能描述:Wireless Data Controller |
发布紧急采购，3分钟左右您将得到回复。