参数资料
| 型号： | X1228S14I-2.7A |
| 厂商： | Intersil |
| 文件页数： | 2/29页 |
| 文件大小： | 0K |
| 描述： | IC RTC/CAL/CPU SUP EE 14-SOIC |
| 标准包装： | 50 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，闰年，监控器，监视计时器 |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电压 - 电源，电池： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOICN |
| 包装： | 管件 |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
10
FN8100.4
May 18, 2006
X1, X2
The X1 and X2 pins are the input and output,
respectively, of an inverting amplifier. An external
32.768kHz quartz crystal is used with the X1228 to
supply a timebase for the real time clock. The
recommended crystal is a Citizen CFS206-32.768KDZF.
Internal compensation circuitry is included to form a
complete oscillator circuit. Care should be taken in the
placement of the crystal and the layout of the circuit.
Plenty of ground plane around the device and short
traces to X1 and X2 are highly recommended. See
Application section for more recommendations.
Figure 1. Recommended Crystal connection
POWER CONTROL OPERATION
The power control circuit accepts a VCC and a VBACK
input. The power control circuit power the clock from
VBACK when VCC < VBACK - 0.2V. It will switch back to
power the device from VCC when VCC exceeds VBACK.
Figure 2. Power Control
REAL TIME CLOCK OPERATION
The Real Time Clock (RTC) uses an external
32.768kHz quartz crystal to maintain an accurate inter-
nal representation of the second, minute, hour, day,
date, month, and year. The RTC has leap-year correc-
tion. The clock also corrects for months having fewer
than 31 days and has a bit that controls 24 hour or
AM/PM format. When the X1228 powers up after the
loss of both VCC and VBACK, the clock will not operate
until at least one byte is written to the clock register.
Reading the Real Time Clock
The RTC is read by initiating a Read command and
specifying the address corresponding to the register of
the Real Time Clock. The RTC Registers can then be
read in a Sequential Read Mode. Since the clock runs
continuously and a read takes a finite amount of time,
there is the possibility that the clock could change during
the course of a read operation. In this device, the time is
latched by the read command (falling edge of the clock
on the ACK bit prior to RTC data output) into a separate
latch to avoid time changes during the read operation.
The clock continues to run. Alarms occurring during a
read are unaffected by the read operation.
Writing to the Real Time Clock
The time and date may be set by writing to the RTC
registers. To avoid changing the current time by an
uncompleted write operation, the current time value is
loaded into a separate buffer at the falling edge of the
clock on the ACK bit before the RTC data input bytes,
the clock continues to run. The new serial input data
replaces the values in the buffer. This new RTC value
is loaded back into the RTC Register by a stop bit at
the end of a valid write sequence. An invalid write
operation aborts the time update procedure and the
contents of the buffer are discarded. After a valid write
operation the RTC will reflect the newly loaded data
beginning with the next “one second” clock cycle after
the stop bit is written. The RTC continues to update
the time while an RTC register write is in progress and
the RTC continues to run during any nonvolatile write
sequences. A single byte may be written to the RTC
without affecting the other bytes.
Accuracy of the Real Time Clock
The accuracy of the Real Time Clock depends on the
frequency of the quartz crystal that is used as the time
base for the RTC. Since the resonant frequency of a
crystal is temperature dependent, the RTC perfor-
mance will also be dependent upon temperature. The
frequency deviation of the crystal is a fuction of the
turnover temperature of the crystal from the crystal’s
nominal frequency. For example, a >20ppm frequency
deviation translates into an accuracy of >1 minute per
month. These parameters are available from the
crystal manufacturer. Intersil’s RTC family provides
on-chip crystal compensation networks to adjust load-
capacitance to tune oscillator frequency from +116
ppm to -37 ppm when using a 12.5 pF load crystal. For
more detail information see the Application section.
X1
X2
VBACK
In
Voltage
VCC
On
Off
X1228
相关PDF资料 |
PDF描述 |
|---|---|
| X1228S14I-2.7 | IC RTC/CAL/CPU SUP EE 14-SOIC |
| X1228S14I | IC RTC/CAL/CPU SUP EE 14-SOIC |
| MCP4252-103E/MF | IC POT DGTL DUAL 10K RHEO 10DFN |
| X1228S14-2.7T1 | IC RTC/CAL/CPU SUP EE 14-SOIC |
| MCP4252-502E/MF | IC POT DGTL DUAL 5K RHEO 10DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X1228S14I-4.5A | 功能描述:IC RTC/CAL/CPU SUP EE 14-SOIC RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 实时时钟 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 类型:时钟/日历 特点:警报器，闰年，SRAM 存储容量:- 时间格式:HH:MM:SS（12/24 小时） 数据格式:YY-MM-DD-dd 接口:SPI 电源电压:2 V ~ 5.5 V 电压 - 电源，电池:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN EP 包装:管件 |
| X1228S14IZ | 功能描述:IC RTC/CAL/SUP/ALRM 4K EE 14SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 实时时钟 系列:- 标准包装:2,500 系列:- 类型:时钟/日历 特点:警报器，闰年，监控器，监视计时器 存储容量:- 时间格式:HH:MM:SS（12/24 小时） 数据格式:YY-MM-DD-dd 接口:I²C，2 线串口 电源电压:2.7 V ~ 5.5 V 电压 - 电源，电池:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
| X1228S14IZ-2.7 | 功能描述:IC RTC/CAL/SUP/ALARM 4K-EE14SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 实时时钟 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 类型:时钟/日历 特点:警报器，闰年，SRAM 存储容量:- 时间格式:HH:MM:SS（12/24 小时） 数据格式:YY-MM-DD-dd 接口:SPI 电源电压:2 V ~ 5.5 V 电压 - 电源，电池:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN EP 包装:管件 |
| X1228S14IZ-2.7A | 功能描述:IC RTC/CAL/CPU SUP EE 14-SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 实时时钟 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 类型:时钟/日历 特点:警报器，闰年，SRAM 存储容量:- 时间格式:HH:MM:SS（12/24 小时） 数据格式:YY-MM-DD-dd 接口:SPI 电源电压:2 V ~ 5.5 V 电压 - 电源，电池:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN EP 包装:管件 |
| X1228S14IZ-4.5A | 功能描述:IC RTC/CAL/CPU SUP EE 14-SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 实时时钟 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 类型:时钟/日历 特点:警报器，闰年，SRAM 存储容量:- 时间格式:HH:MM:SS（12/24 小时） 数据格式:YY-MM-DD-dd 接口:SPI 电源电压:2 V ~ 5.5 V 电压 - 电源，电池:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN EP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。