参数资料
| 型号： | X40014V8-A |
| 厂商： | Intersil |
| 文件页数： | 2/24页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE MONITOR DUAL 8-TSSOP |
| 标准包装： | 100 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 高有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 1.3V，2.9V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 管件 |
X40010, X40011, X40014, X40015
Low V CC detection circuitry protects the user’s system
from low voltage conditions, resetting the system
when V CC falls below the minimum V TRIP1 point.
RESET/RESET is active until V CC returns to proper
operating level and stabilizes. A second voltage moni-
tor circuit tracks the unregulated supply to provide a
power fail warning or monitors different power supply
voltage. Three common low voltage combinations are
available, however, Intersil’s unique circuits allows the
threshold for either voltage monitor to be repro-
The Watchdog Timer provides an independent protec-
tion mechanism for microcontrollers. When the micro-
controller fails to restart a timer within a selectable
time out interval, the device activates the WDO signal.
The user selects the interval from three preset values.
Once selected, the interval does not change, even
after cycling the power.
The device features a 2-wire interface and software
protocol allowing operation on an I 2 C ? bus.
grammed to meet special needs or to fine-tune the
threshold for applications requiring higher precision.
Dual Voltage Monitors
Table 1:
Device
X40010/11
-A
-B
-C
X40014/15
-A
-B
-C
Expected System Voltages
5V; 3V or 3.3V
5V; 3V
3V; 3.3V; 1.8V
3V; 3.3V; 1.5V
3V; 1.5V
3V or 3.3V; 1.1 or 1.2V
Vtrip1(V)
2.0–4.75*
4.55–4.65*
4.35–4.45*
2.85–2.95*
2.0–4.75*
2.85–2.95*
2.55–2.65*
2.85–2.95*
Vtrip2(V)
1.70–4.75
2.85–2.95
2.55–2.65
1.65–1.75
0.90–3.50*
1.25–1.35*
1.25–1.35*
0.95–1.05*
POR (system)
RESET = X40010
RESET = X40011
RESET = X40014
RESET = X40015
*Voltage monitor requires V CC to operation. Others are independent of V CC .
PIN CONFIGURATION
X40010/14, X40011/15
8-Pin SOIC
X40010/14, X40011/15
8-Pin TSSOP
V2FAIL
V2MON
RESET/RESET
V SS
1
2
3
4
8
7
6
5
V CC
WDO
SCL
SDA
WDO
V CC
V2FAIL
V2MON
1
2
3
4
8
7
6
5
SCL
SDA
V SS
RESET/RESET
PIN DESCRIPTION
Pin
SOIC TSSOP Name Function
1 3 V2FAIL V2 Voltage Fail Output. This open drain output goes LOW when V2MON is less than V TRIP2 and
goes HIGH when V2MON exceeds V TRIP2 . There is no power up reset delay circuitry on this pin.
2 4 V2MON V2 Voltage Monitor Input. When the V2MON input is less than the V TRIP2 voltage, V2FAIL goes
LOW. This input can monitor an unregulated power supply with an external resistor divider or can
monitor a second power supply with no external components. Connect V2MON to V SS or V CC when
not used.The V2MON comparator is supplied by V2MON (X40010/11) or by V CC Input (X40014/15).
3 5 RESET/ RESET Output. (X40011/15) This is an active LOW, open drain output which goes active whenever
RESET V CC falls below V TRIP1 . It will remain active until V CC rises above V TRIP1 and for the t PURST thereafter.
RESET Output. (X40010/14) This is an active HIGH CMOS output which goes active whenever V CC
falls below V TRIP1 . It will remain active until V CC rises above V TRIP1 and for the t PURST thereafter.
4 6 V SS
5 7 SDA
Ground
Serial Data. SDA is a bidirectional pin used to transfer data into and out of the device. It has an open
drain output and may be wire ORed with other open drain or open collector outputs. This pin requires
a pull up resistor and the input buffer is always active (not gated).
Watchdog Input. A HIGH to LOW transition on the SDA (while SCL is toggled from HIGH to
LOW and followed by a stop condition) restarts the Watchdog timer. The absence of this transi-
tion within the watchdog time out period results in WDO going active.
2
FN8111.0
March 28, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| ABC26DRTS | CONN EDGECARD 52POS .100 DIP SLD |
| ISL6422ERZ-T | IC VREG DUAL LNB W/I2C 40-QFN |
| ISL6556BCRZA | IC CTRLR MULTIPHASE VRM10 32-QFN |
| X40014S8I-CT1 | IC VOLTAGE MONITOR DUAL 8-SOIC |
| ISL6556BCRZ | IC CTRLR MULTIPHASE VRM10 32-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X40014V8-AT1 | 功能描述:IC VOLTAGE MONITOR DUAL 8-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40014V8-B | 功能描述:IC VOLTAGE MONITOR DUAL 8-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40014V8-BT1 | 功能描述:IC VOLTAGE MONITOR DUAL 8-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40014V8-C | 功能描述:IC VOLTAGE MONITOR DUAL 8-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40014V8-CT1 | 功能描述:IC VOLTAGE MONITOR DUAL 8-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。