参数资料
| 型号： | X40015V8I-CT1 |
| 厂商： | Intersil |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE MONITOR DUAL 8-TSSOP |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 1V，2.9V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 带卷 (TR) |
X40010, X40011, X40014, X40015
Figure 7. Valid Start and Stop Conditions
SCL
SDA
Start
Serial Acknowledge
Acknowledge is a software convention used to indi-
cate successful data transfer. The transmitting device,
either master or slave, will release the bus after trans-
mitting eight bits. During the ninth clock cycle, the
receiver will pull the SDA line LOW to acknowledge
that it received the eight bits of data. See Figure 8.
The device will respond with an acknowledge after
recognition of a start condition and if the correct
Device Identifier and Select bits are contained in the
Slave Address Byte. If a write operation is selected,
the device will respond with an acknowledge after the
receipt of each subsequent eight bit word. The device
will acknowledge all incoming data and address bytes,
except for the Slave Address Byte when the Device
Identifier and/or Select bits are incorrect.
In the read mode, the device will transmit eight bits of
data, release the SDA line, then monitor the line for an
acknowledge. If an acknowledge is detected and no
stop condition is generated by the master, the device
will continue to transmit data. The device will terminate
further data transmissions if an acknowledge is not
Stop
detected. The master must then issue a stop condition
to return the device to Standby mode and place the
device into a known state.
Serial Write Operations
Byte Write
For a write operation, the device requires the Slave
Address Byte and a Word Address Byte. This gives
the master access to any one of the words in the
array. After receipt of the Word Address Byte, the
device responds with an acknowledge, and awaits the
next eight bits of data. After receiving the 8 bits of the
Data Byte, the device again responds with an
acknowledge. The master then terminates the transfer
by generating a stop condition, at which time the
device begins the internal write cycle to the nonvolatile
memory. During this internal write cycle, the device
inputs are disabled, so the device will not respond to any
requests from the master. The SDA output is at high
impedance. See Figure 9.
A write to a protected block of memory will suppress
the acknowledge bit.
Figure 8. Acknowledge Response From Receiver
SCL from
Master
1
8
9
Data Output
from
Data Output
from Receiver
Start
9
Acknowledge
FN8111.0
March 28, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| X40021V14I-CT1 | IC VOLTAGE MONITOR DUAL 14-TSSOP |
| X40035V14I-CT1 | IC VOLTAGE MONITOR TRPL 14-TSSOP |
| X4005S8I-4.5A | IC SUPERVISOR CPU I2C 8-SOIC |
| X40239S16I-BT1 | IC VOLTAGE MON TRPL EE 16-SOIC |
| X40415V8I-CT1 | IC VOLTAGE MON DUAL W/SUP 8TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X40020 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual Voltage Monitor with Intergrated CPU Supervisor and System Battery Switch |
| X40020_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual Voltage Monitor with Integrated CPU Supervisor and System Battery Switch |
| X40020S14-A | 功能描述:IC VOLTAGE MONITOR DUAL 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40020S14-AT1 | 功能描述:IC VOLTAGE MONITOR DUAL 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40020S14-B | 功能描述:IC VOLTAGE MONITOR DUAL 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。