参数资料
| 型号： | X40233S16I-BT1 |
| 厂商： | Intersil |
| 文件页数： | 13/36页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE MON TRPL EE 16-SOIC |
| 标准包装： | 1,000 |
| 类型： | 多压监控器 |
| 监视电压数目： | 3 |
| 输出： | 开路漏极，开路漏极 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 1.75V，2.95V，4.45V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
X40231, X40233, X40235, X40237, X40239
S 1
0
1
0
1
1
1
0
A WT
0
0
0
0
0
P1 P0
A
D7 D6 D5 D4 D3 D2 D1 D0
A
S
T
A
R
T
SLAVE ADDRESS BYTE
C
K
INSTRUCTION BYTE
C
K
DATA BYTE
C
K
T
O
P
DCP Write Operation
Figure 9.
DCP Write Command Sequence
Using a Data Byte larger than the values specified
A write to DCPx (x=0,1,2) can be performed using the
three byte command sequence shown in Figure 9.
In order to perform a write operation on a particular
DCP, the Write Enable Latch (WEL) bit of the CR Reg-
ister must first be set (See “BL1, BL0: Block Lock pro-
tection bits - (Nonvolatile)” on page 18.)
The Slave Address Byte 10101110 specifies that a
Write to a DCP is to be conducted. An ACKNOWL-
EDGE is returned by the X4023x after the Slave
Address, if it has been received correctly.
Next, an Instruction Byte is issued on SDA. Bits P1
and P0 of the Instruction Byte determine which WCR
is to be written, while the WT bit determines if the
Write is to be volatile or nonvolatile. If the Instruction
Byte format is valid, another ACKNOWLEDGE is then
returned by the X4023x.
Following the Instruction Byte, a Data Byte is issued to
the X4023x over SDA. The Data Byte contents is
latched into the WCR of the DCP on the first rising
edge of the clock signal, after the LSB of the Data Byte
(D0) has been issued on SDA (See Figure 34).
The Data Byte determines the “wiper position” (which
FET switch of the DCP resistive array is switched ON)
of the DCP. The maximum value for the Data Byte
depends upon which DCP is being addressed (see fol-
lowing table).
above results in the “wiper terminal” being set to the
highest tap position. The “wiper position” does NOT
roll-over to the lowest tap position.
For DCP0 (64 Tap) and DCP2 (256 Tap), the Data
Byte maps one to one to the “wiper position” of the
DCP “wiper terminal”. Therefore, the Data Byte
00001111 (15 10 ) corresponds to setting the “wiper ter-
minal” to tap position 15. Similarly, the Data Byte
00011100 (28 10 ) corresponds to setting the “wiper ter-
minal” to tap position 28. The mapping of the Data
Byte to “wiper position” data for DCP1 (100 Tap), is
shown in “APPENDIX 1” . An example of a simple C
language function which “translates” between the tap
position (decimal) and the Data Byte (binary) for
DCP1, is given in “APPENDIX 2” .
It should be noted that all writes to any DCP of the
X4023x are random in nature. Therefore, the Data
Byte of consecutive write operations to any DCP can
differ by an arbitrary number of bits. Also, setting the
bits P1 = 1, P0 = 1 is a reserved sequence, and will
result in no ACKNOWLEDGE after sending an Instruc-
tion Byte on SDA.
The factory default setting of all “wiper position” set-
tings is with 00h stored in the NVM of the DCPs. This
corresponds to having the “wiper terminal” R WX
(x = 0,1,2) at the “lowest” tap position, Therefore, the
resistance between R WX and R LX is a minimum
(essentially only the Wiper Resistance, R W ).
P1- P0
DCPx
# Taps
Max. Data Byte
0
0
1
0
1
0
x=0
x=1
x=2
64
100
256
3Fh
Refer to Appendix 1
FFh
1
1
13
Reserved
FN8115.0
April 11, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| AGM12DTMN-S664 | CONN EDGECARD 24POS R/A .156 |
| AYM10DTMT-S664 | CONN EDGECARD 20POS R/A .156 |
| ISL6322IRZ-T | IC CTRLR PWM 4PHASE BUCK 48-QFN |
| ASM08DTBS | CONN EDGECARD 16POS R/A .156 SLD |
| AYM12DTMN-S664 | CONN EDGECARD 24POS R/A .156 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X40235 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP |
| X40235S16I-A | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40235S16I-AT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40235S16I-B | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40235S16I-BT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。