参数资料
| 型号： | X40237S16I-A |
| 厂商： | Intersil |
| 文件页数： | 23/36页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE MON TRPL EE 16-SOIC |
| 标准包装： | 94 |
| 类型： | 多压监控器 |
| 监视电压数目： | 3 |
| 输出： | 开路漏极，开路漏极 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 1.75V，2.2V，2.95V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
X40231, X40233, X40235, X40237, X40239
Setting a Higher V TRIPx Voltage (x = 1,2,3)
To set a V TRIPx threshold to a new voltage which is
higher than the present threshold, the user must apply
the desired V TRIPx threshold voltage to the correspond-
ing input pin (V CC , V2MON or V3MON). Then, a pro-
gramming voltage (Vp) must be applied to the WP pin
before a START condition is set up on SDA. Next, issue
on the SDA pin the Slave Address A0h, followed by the
Byte Address 01h for V TRIP1 , 09h for V TRIP2 , and 0Dh
for V TRIP3 , and a 00h Data Byte in order to program
V TRIPx . The STOP bit following a valid write operation
initiates the programming sequence. Pin WP must then
be brought LOW to complete the operation (See Figure
23). The user does not have to set the WEL bit in the
CR register before performing this write sequence.
Setting a Lower V TRIPx Voltage (x = 1,2,3).
In order to set V TRIPx to a lower voltage than the
present value, then V TRIPx must first be “reset” accord-
ing to the procedure described below. Once V TRIPx
has been “reset”, then V TRIPx can be set to the desired
voltage using the procedure described in “Setting a
Higher V TRIPx Voltage”.
Resetting the V TRIPx Voltage (x = 1,2,3).
To reset a V TRIPx voltage, apply the programming volt-
age (Vp) to the WP pin before a START condition is
set up on SDA. Next, issue on the SDA pin the Slave
Address A0h followed by the Byte Address 03h for
V TRIP1 , 0Bh for V TRIP2 , and 0Fh for V TRIP3 , followed
by 00h for the Data Byte in order to reset V TRIPx . The
STOP bit following a valid write operation initiates the
programming sequence. Pin WP must then be brought
LOW to complete the operation (See Figure 23). The
user does not have to set the WEL bit in the CR regis-
ter before performing this write sequence.
V P
WP
After being reset, the value of V TRIPx becomes a nomi-
nal value of 1.7V.
V TRIPx Accuracy (x = 1,2,3).
The accuracy with which the V TRIPx thresholds are set,
can be controlled using the iterative process shown in
Figure 24.
If the desired threshold is less that the present thresh-
old voltage, then it must first be “reset” (See "Resetting
the V TRIPx Voltage (x = 1,2,3).").
The desired threshold voltage is then applied to the
appropriate input pin (V CC , V2MON or V3MON) and
the procedure described in Section “Setting a Higher
V TRIPx Voltage“ must be followed.
Once the desired V TRIPx threshold has been set, the
error between the desired and (new) actual set thresh-
old can be determined. This is achieved by applying
V CC to the device, and then applying a test voltage
higher than the desired threshold voltage, to the input
pin of the voltage monitor circuit whose V TRIPx was
programmed. For example, if V TRIP2 was set to a
desired level of 3.0 V, then a test voltage of 3.4 V may
be applied to the voltage monitor input pin V2MON. In
the case of setting of V TRIP1 then only V CC need be
applied. In all cases, care should be taken not to
exceed the maximum input voltage limits.
After applying the test voltage to the voltage monitor
input pin, the test voltage can be decreased (either in
discrete steps, or continuously) until the output of the
voltage monitor circuit changes state. At this point, the
error between the actual/measured, and desired
threshold levels is calculated.
SCL
SDA
S
T
A
R
0 1 2 3 4 5 6 7
A0h ?
0 1 2 3 4 5 6 7
03h ? Resets VTRIP1
0Bh ? Resets VTRIP2
0Fh ? Resets VTRIP3
0 1 2 3 4 5 6 7
00h ?
Data Byte
T
23
Figure 23. Resetting the V TRIPx Level
? All
others Reserved.
FN8115.0
April 11, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| 250VXR1200MEFCSN35X45 | CAP ALUM 1200UF 250V 20% SNAP-IN |
| GSC26DRTS-S734 | CONN EDGECARD 52POS DIP .100 SLD |
| 0925-822K | COIL RF 8.2UH MOLDED SHIELDED |
| GSM43DRUS | CONN EDGECARD 86POS DIP .156 SLD |
| ISL6322CRZ | IC CTRLR PWM 4PHASE BUCK 48-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X40237S16I-AT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40237S16I-B | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40237S16I-BT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40239 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP |
| X40239S16I-A | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。