参数资料
| 型号： | X40415V8I-CT1 |
| 厂商： | Intersil |
| 文件页数： | 5/24页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE MON DUAL W/SUP 8TSSOP |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 1V，2.9V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 带卷 (TR) |
X40410, X40411, X40414, X40415
Resetting the V TRIPx Voltage
To reset a V TRIPx voltage, apply the programming volt-
age (Vp) to the WDO pin before a START condition is
set up on SDA. Next, issue on the SDA pin the Slave
Address A0h followed by the Byte Address 03h for
V TRIP1 and 0Bh for V TRIP2 , followed by 00h for the
Data Byte in order to reset V TRIPx . The STOP bit fol-
lowing a valid write operation initiates the program-
ming sequence. Pin WDO must then be brought LOW
to complete the operation.
After being reset, the value of V TRIPx becomes a nomi-
nal value of 1.7V or lesser.
Note: This operation does not corrupt the memory
array.
CONTROL REGISTER
The Control Register provides the user a mechanism for
operation directly to the address of the register and only
one data byte is allowed for each register write operation.
Prior to writing to the Control Register, the WEL and
RWEL bits must be set using a two step process, with
the whole sequence requiring 3 steps. See "Writing to
the Control Registers" on page 7.
The user must issue a stop, after sending this byte to
the register, to initiate the nonvolatile cycle that stores
WD1, WD0, PUP1, PUP0, BP1, and BP0. The
X40410/11/14/15 will not acknowledge any data bytes
written after the first byte is entered.
The state of the Control Register can be read at any
time by performing a random read at address 01Fh,
using the special preamble. Only one byte is read by
each register read operation. The master should sup-
ply a stop condition to be consistent with the bus pro-
tocol, but a stop is not required to end this operation.
changing the Block Lock and Watchdog Timer settings.
7
6
5
4
3
2
1
0
The Block Lock and Watchdog Timer bits are nonvolatile
PUP1 WD1
WD0
BP
0
RWEL WEL PUP0
and do not change when power is removed.
The Control Register is accessed with a special pream-
ble in the slave byte (1011) and is located at address
1FFh. It can only be modified by performing a byte write
RWEL: Register Write Enable Latch (Volatile)
The RWEL bit must be set to “1” prior to a write to the
Control Register.
Figure 4. Sample V TRIP Reset Circuit
V P
Adjust
V TRIP1
Adj.
V2FAIL
RESET
1 8
3 SOIC 7
2 X4041x 6
4
5
Run
SCL
μC
V TRIP2
Adj.
5
4.7K
SDA
FN8116.0
March 28, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| X40421V14I-CT1 | IC VOLT MON DUAL SUP/SW 14-TSSOP |
| X40435V14I-CT1 | IC VOLT MON TRPL EEPROM 14-TSSOP |
| X4045S8T1 | IC SUPERVISOR CPU 4K EE 8-SOIC |
| X40626V14T1 | IC SUPERVISOR CPU DUAL 14-TSSOP |
| X4165V8I-4.5A | IC SUPERVISOR CPU 16K EE 8-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X40415V8IZ-B | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| X40415V8IZ-BT1 | 制造商:Intersil Corporation 功能描述:PB-FREE, DUAL SUPERVISORS (MONITOR/FLAG PAIRS) W/ 4K EPROM, - Tape and Reel |
| X40420 | 制造商:XICOR 制造商全称:Xicor Inc. 功能描述:Dual Voltage Monitor with Integrated CPU Supervisor and System Battery Switch |
| X40420_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual Voltage Monitor with Integrated CPU Supervisor and System Battery Switch |
| X40420S14-A | 功能描述:IC VOLT MON DUAL SUP/SW 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。