参数资料
| 型号： | X40431V14-A |
| 厂商： | Intersil |
| 文件页数： | 16/26页 |
| 文件大小： | 0K |
| 描述： | IC VOLT MON TRPL EEPROM 14-TSSOP |
| 标准包装： | 95 |
| 类型： | 多压监控器 |
| 监视电压数目： | 3 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 1.7V，2.9V，4.6V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
X40430, X40431, X40434, X40435
SERIAL DEVICE ADDRESSING
Memory Address Map
CR, Control Register, CR7: CR0
Address: 1FF hex
FDR, Fault DetectionRegister, FDR7: FDR0
Address: 0FF hex
General Purpose Memory Organization, A8:A0
Address: 000h to 1FFh
General Purpose Memory Array Configuration
– last bit of the slave command byte is a R/W bit. The
R/W bit of the Slave Address Byte defines the oper-
ation to be performed. When the R/W bit is a one,
then a read operation is selected. A zero selects a
write operation.
Word Address
The word address is either supplied by the master or
obtained from an internal counter. The internal counter
is undefined on a power-up condition.
Operational Notes
Memory Address
A8:A0
000h
0FFh
100h
1FFh
Lower 256 bytes
Upper 256 bytes
Block Protect Option
The device powers-up in the following state:
– The device is in the low power standby state.
– The WEL bit is set to ‘0’. In this state it is not possi-
ble to write to the device.
– SDA pin is the input mode.
– RESET/RESET Signal is active for t PURST .
Slave Address Byte
Following a start condition, the master must output a
Slave Address Byte. This byte consists of several parts:
– a device type identifier that is always ‘101x’. Where
x = 0 is for Array, x = 1 is for Control Register or
Fault Detection Register.
– next two bits are ‘0’.
– next bit that becomes the MSB of the address.
Figure 14. X40430, X40431, X40434, X40435
Addressing
Data Protection
The following circuitry has been included to prevent
inadvertent writes:
– The WEL bit must be set to allow write operations.
– The proper clock count and bit sequence is required
prior to the stop bit in order to start a nonvolatile
write cycle.
– A three step sequence is required before writing into
the Control Register to change Watchdog Timer or
Block Lock settings.
General Purpose Memory
Slave Byte
1 0
1
0
0
0
A8 R/W
– The WP pin, when held HIGH, prevents all writes to
the array and all the Register.
Control Register
Fault Detection Register
1
1
0
0
1
1
1
1
0
0
0
0
1
0
R/W
R/W
Word Address
General Purpose Memory A7
A6 A5 A4 A3 A2 A1
A0
Control Register
Fault Detection Register
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Figure 15. Current Address Read Sequence
.
16
Signals from
the Master
SDA Bus
Signals from
the Slave
S
t
a
r
t
Slave
Address
1 0 1 0 0 0
1
A
C
K
Data
S
t
o
p
FN8251.1
May 24, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| ESC30DREN-S734 | CONN EDGECARD 60POS .100 EYELET |
| AHA337M06X16T-F | CAP ALUM 330UF 6.3V 20% SMD |
| RMC30DREI-S13 | CONN EDGECARD 60POS .100 EXTEND |
| X40431S14I-CT1 | IC VOLT MON TRPL EEPROM 14-SOIC |
| UUX2A470MNL1GS | CAP ALUM 47UF 100V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X40431V14-AT1 | 功能描述:IC VOLT MON TRPL EEPROM 14-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40431V14-B | 功能描述:IC VOLT MON TRPL EEPROM 14-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40431V14-BT1 | 功能描述:IC VOLT MON TRPL EEPROM 14-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40431V14-C | 功能描述:IC VOLT MON TRPL EEPROM 14-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40431V14-CT1 | 功能描述:IC VOLT MON TRPL EEPROM 14-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。