- 您现在的位置：买卖IC网 > PDF目录15091 > X4043M8ZT1 (Intersil)IC CPU SUPERV 4K EEPROM 8-MSOP PDF资料下载
参数资料
| 型号： | X4043M8ZT1 |
| 厂商： | Intersil |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | IC CPU SUPERV 4K EEPROM 8-MSOP |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 2,500 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 4.38V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
X4043, X4045
Setting a V TRIP Voltage
There are two procedures used to set the threshold
voltages (V TRIP ), depending if the threshold voltage to
be stored is higher or lower than the present value. For
example, if the present V TRIP is 2.9 V and the new
V TRIP is 3.2 V, the new voltage can be stored directly
into the V TRIP cell. If however, the new setting is to be
lower than the present setting, then it is necessary to
“reset” the V TRIP voltage before setting the new value.
Setting a Higher V TRIP Voltage
To set a V TRIP threshold to a new voltage which is
higher than the present threshold, the user must apply
the desired V TRIP threshold voltage to the V CC . Then,
a programming voltage (Vp) must be applied to the
WP pin before a START condition is set up on SDA.
Next, issue on the SDA pin the Slave Address A0h,
followed by the Byte Address 01h for V TRIP and a 00h
Data Byte in order to program V TRIP . The STOP bit
following a valid write operation initiates the program-
ming sequence. WP pin must then be brought LOW to
complete the operation.
To check if the V TRIP has been set, first power-down
the device. Slowly ramp up V CC and observe when the
output, RESET (4043) or RESET (4045) switches. The
voltage at which this occurs is the V TRIP (actual) (see
Figure 2).
C ASE A
Now if the desired V TRIP is greater than the V TRIP
(actual), then add the difference between V TRIP
(desired) - V TRIP (actual) to the original V TRIP desired.
This is your new V TRIP that should be applied to V CC
and the whole sequence should be repeated again
(see Figure 5).
6
C ASE B
Now if the V TRIP (actual), is higher than the V TRIP
(desired), perform the reset sequence as described in
the next section. The new V TRIP voltage to be applied to
V CC will now be: V TRIP (desired) - (V TRIP (actual) - V TRIP
(desired)).
Note: This operation does not corrupt the memory
array.
Setting a Lower V TRIP Voltage
In order to set V TRIP to a lower voltage than the
present value, then V TRIP must first be “reset” accord-
ing to the procedure described below. Once V TRIP has
been “reset”, then V TRIP can be set to the desired volt-
age using the procedure described in “Setting a Higher
V TRIP Voltage”.
Resetting the V TRIP Voltage
To reset a V TRIP voltage, apply the programming volt-
age (Vp) to the WP pin before a START condition is
set up on SDA. Next, issue on the SDA pin the Slave
Address A0h followed by the Byte Address 03h fol-
lowed by 00h for the Data Byte in order to reset V TRIP .
The STOP bit following a valid write operation initiates
the programming sequence. Pin WP must then be
brought LOW to complete the operation.
After being reset, the value of V TRIP becomes a nomi-
nal value of 1.7V or lesser.
Note: This operation does not corrupt the memory
array.
FN8118.2
March 16, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| AFK688M06P44B-F | CAP ALUM 6800UF 6.3V 20% SMD |
| AFK687M50P44B-F | CAP ALUM 680UF 50V 20% SMD |
| AFK478M10P44B-F | CAP ALUM 4700UF 10V 20% SMD |
| AFK338M16P44B-F | CAP ALUM 3300UF 16V 20% SMD |
| AFK158M35P44B-F | CAP ALUM 1500UF 35V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X4043P | 功能描述:IC CPU SUPERV 4K EE RST LO 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X4043P-2.7 | 功能描述:IC CPU SUPERV 4K EE RST LO 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:标准传输延迟为 60 µs 电压 - 阀值:3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 其它名称:LM8364BALMF30DKR |
| X4043P-2.7A | 功能描述:IC SUPERVISOR CPU 4K EE 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4043P-4.5A | 功能描述:IC SUPERVISOR CPU 4K EE 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4043P8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。