参数资料
| 型号： | X40626V14 |
| 厂商： | Intersil |
| 文件页数： | 15/22页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR CPU DUAL 14-TSSOP |
| 标准包装： | 190 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 2.93V，4.38V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
X40626
ABSOLUTE MAXIMUM RATINGS
Temperature under bias ................... -65°C to +135°C
Storage temperature ........................ -65°C to +150°C
Voltage on any pin with respect to VSS... -1.0V to +7V
D.C. output current (sink) ................................... 10mA
Lead temperature (soldering, 10 seconds) ........ 300°C
Table 2. Recommended Operating Conditions
COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability.
Temp
Commercial
Industrial
Min.
0°C
-40°C
Max.
70°C
+85°C
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
V CC = 2.7 to 5.5V
Symbol
I CC1(1)
I CC2(2)
I SB1(2)
Parameter
Active Supply Current Read
Active Supply Current Write
Standby Current DC (WDT off)
Min
Max
1.0
3.0
1
Unit
mA
mA
μ A
Test Conditions
V IL = V CC x 0.1, V IH = V CC x 0.9
f SCL = 400kHz, SDA = Open
V SDA =V SCL =V CC
Others=GND or V CC
I SB2(3)
Standby Current DC (WDT on)
30
μ A
V SDA =V SCL =V CC
Others=GND or V CC
I LI
I LO
Input Leakage Current
Output Leakage Current
10
10
μ A
μ A
V IN = GND to V CC
V SDA = GND to V CC
Device is in Standby
V IL
V IH
Input LOW Voltage
Input HIGH Voltage
-1
V CC x 0.7
V CC x 0.3
V CC +0.5
V
V
V HYS
Schmitt Trigger Input Hysteresis
Fixed input level
V CC related level
0.2
.05 x V CC
V
V
V OL
Output LOW Voltage
0.4
V
I OL = 1.0mA (V CC =3V)
I OL = 3.0mA (V CC =5V)
Notes: (1) The device enters the Active state after any start, and remains active until: (a) 9 clock cycles later if the Device Select Bits in the Slave
Address Byte are incorrect; or (b) 200nS after a stop ending a read operation.
(2) The device enters the Active state after any start, and remains active until t WC after a stop ending a write operation.
(3) The device goes into Standby: (a) 200nS after any stop, except those that initiate a nonvolatile write cycle; or (b) t WC after a stop that
initiates a nonvolatile cycle; or 9 clock cycles after any start that is not followed by the correct Device Select Bits in the Slave Address
Byte.
15
FN8119.0
March 28, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| 100LSQ27000MEFC64X99 | CAP ALUM 27000UF 100V 20% SCREW |
| X40626S14T1 | IC SUPERVISOR CPU DUAL 14-SOIC |
| 200LSQ10000MEFC64X119 | CAP ALUM 10000UF 200V 20% SCREW |
| 250LSQ6800MEFC64X119 | CAP ALUM 6800UF 250V 20% SCREW |
| TVX1C220MAD | CAP ALUM 22UF 16V 20% AXIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X40626V14-2.7 | 功能描述:IC SUPERVISOR CPU DUAL 14-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40626V14-2.7A | 功能描述:IC SUPERVISOR CPU DUAL 14-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40626V14-2.7AT1 | 功能描述:IC SUPERVISOR CPU DUAL 14-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40626V14-2.7T1 | 功能描述:IC SUPERVISOR CPU DUAL 14-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40626V14-4.5A | 功能描述:IC SUPERVISOR CPU DUAL 14-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。