- 您现在的位置：买卖IC网 > PDF目录297797 > X4163S8Z (INTERSIL CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | X4163S8Z |
| 厂商： | INTERSIL CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封装： | ROHS COMPLIANT, SOIC-8 |
| 文件页数： | 2/22页 |
| 文件大小： | 342K |
| 代理商： | X4163S8Z |
10
FN8120.2
November 26, 2007
Figure 6. Valid Start and Stop Conditions
Serial Start Condition
All commands are preceded by the start condition,
which is a HIGH to LOW transition of SDA when SCL
is HIGH. The device continuously monitors the SDA
and SCL lines for the start condition and will not
respond to any command until this condition has been
met. See Figure 6.
Serial Stop Condition
All communications must be terminated by a stop con-
dition, which is a LOW to HIGH transition of SDA when
SCL is HIGH. The stop condition is also used to place
the device into the Standby power mode after a read
sequence. A stop condition can only be issued after the
transmitting device has released the bus. See Figure 6.
Serial Acknowledge
Acknowledge is a software convention used to indi-
cate successful data transfer. The transmitting device,
either master or slave, will release the bus after trans-
mitting eight bits. During the ninth clock cycle, the
receiver will pull the SDA line LOW to acknowledge
that it received the eight bits of data. Refer to Figure 7.
The device will respond with an acknowledge after
recognition of a start condition and if the correct
Device Identifier and Select bits are contained in the
Slave Address Byte. If a write operation is selected,
the device will respond with an acknowledge after the
receipt of each subsequent eight bit word. The device
will acknowledge all incoming data and address bytes,
except for the Slave Address Byte when the Device
Identifier and/or Select bits are incorrect.
In the read mode, the device will transmit eight bits of
data, release the SDA line, then monitor the line for an
acknowledge. If an acknowledge is detected and no
stop condition is generated by the master, the device
will continue to transmit data. The device will terminate
further data transmissions if an acknowledge is not
detected. The master must then issue a stop condition
to return the device to Standby mode and place the
device into a known state.
Figure 7. Acknowledge Response From Receiver
SCL
SDA
Start
Stop
Data Output
from
Transmitter
Data Output
from Receiver
8
1
9
Start
Acknowledge
SCL from
Master
X4163, X4165
相关PDF资料 |
PDF描述 |
|---|---|
| X4165V8-2.7 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X4165S8-4.5A | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X5001S8-1.8 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| X5043V14I-2.7A | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| X5045M8I-4.5A | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X4163S8Z-2.7 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CPU Supervisor with 16K EEPROM |
| X4163S8Z-2.7A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CPU Supervisor with 16K EEPROM |
| X4163S8Z-4.5A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CPU Supervisor with 16K EEPROM |
| X4163V8 | 功能描述:IC SUPERVISOR CPU 16K EE 8-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4163V8-2.7 | 功能描述:IC SUPERVISOR CPU 16K EE 8-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。