参数资料
| 型号： | X4283S8I-4.5A |
| 厂商： | Intersil |
| 文件页数： | 16/22页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR CPU 128K EE 8-SOIC |
| 标准包装： | 100 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 4.62V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 管件 |
X4283, X4285
ABSOLUTE MAXIMUM RATINGS
Temperature under bias ................... -65°C to +135°C
Storage temperature ........................ -65°C to +150°C
Voltage on any pin with
respect to V SS ...................................... -1.0V to +7V
D.C. output current ............................................... 5mA
Lead temperature (soldering, 10s) .................... 300°C
COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability
.
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Min.
0°C
-40°C
Max.
70°C
+85°C
Option
-2.7 and -2.7A
Blank and -4.5A
Supply Voltage Limits
2.7V to 5.5V
4.5V to 5.5V
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
V CC = 2.7 to 5.5V
Symbol
Parameter
Min
Max
Unit
Test Conditions
I CC1
I CC2
(1)
(1)
Active Supply Current Read
Active Supply Current Write
1.0
3.0
mA
mA
V IL = V CC x 0.1, V IH = V CC x 0.9
f SCL = 400kHz, SDA = Commands
I SB1
(2)
Standby Current DC (WDT off)
1
μA
V SDA = V SCL = V SB
Others = GND or V SB
I SB2(2)
I LI
I LO
Standby Current DC (WDT on)
Input Leakage Current
Output Leakage Current
20
10
10
μA
μA
μA
V SDA = V SCL = V SB
Others = GND or V SB
V IN = GND to V CC
V SDA = GND to V CC
Device is in Standby (2)
V IL(3)
V IH(3)
V HYS
Input LOW Voltage
Input nonvolatile
Schmitt Trigger Input Hysteresis
Fixed input level
V CC related level
-0.5
V CC x 0.7
0.2
.05 x V CC
V CC x 0.3
V CC +0.5
V
V
V
V
V OL
Output LOW Voltage
0.4
V
I OL = 3.0mA (2.7-5.5V)
Notes: (1) The device enters the Active state after any start, and remains active until: 9 clock cycles later if the Device Select Bits in the Slave
Address Byte are incorrect; 200ns after a stop ending a read operation; or t WC after a stop ending a write operation.
(2) The device goes into Standby: 200ns after any stop, except those that initiate a nonvolatile write cycle; t WC after a stop that initiates a
nonvolatile cycle; or 9 clock cycles after any start that is not followed by the correct Device Select Bits in the Slave Address Byte.
(3) V IL Min. and V IH Max. are for reference only and are not tested.
16
FN8121.1
May 23, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| X4283S8I-2.7AT1 | IC SUPERVISOR CPU 128K EE 8-SOIC |
| X4283S8I-2.7A | IC SUPERVISOR CPU 128K EE 8-SOIC |
| X4283S8-4.5A | IC SUPERVISOR CPU 128K EE 8-SOIC |
| GBB25DHBN | CONN EDGECARD 50POS R/A .050 SLD |
| GBB25DHBD | CONN EDGECARD 50POS R/A .050 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X4283S8IZ | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CPU Supervisor with 128K EEPROM |
| X4283S8IZ-2.7 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CPU Supervisor with 128K EEPROM |
| X4283S8IZ-2.7A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CPU Supervisor with 128K EEPROM |
| X4283S8Z | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CPU Supervisor with 128K EEPROM |
| X4283S8Z-2.7 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CPU Supervisor with 128K EEPROM |
发布紧急采购，3分钟左右您将得到回复。