- 您现在的位置：买卖IC网 > PDF目录376443 > X5329V14Z-4.5A (INTERSIL CORP) RTC Module With CPU Supervisor PDF资料下载
参数资料
| 型号： | X5329V14Z-4.5A |
| 厂商： | INTERSIL CORP |
| 元件分类： | 电源管理 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| 封装： | ROHS COMPLIANT, PLASTIC, TSSOP-14 |
| 文件页数： | 9/21页 |
| 文件大小： | 347K |
| 代理商： | X5329V14Z-4.5A |
9
FN8132.1
October 17, 2005
Read Sequence
When reading from the EEPROM memory array, CS is
first pulled low to select the device. The 8-bit READ
instruction is transmitted to the device, followed by the
16-bit address. After the READ opcode and address
are sent, the data stored in the memory at the selected
address is shifted out on the SO line. The data stored
in memory at the next address can be read sequen-
tially by continuing to provide clock pulses. The
address is automatically incremented to the next
higher address after each byte of data is shifted out.
When the highest address is reached, the address
counter rolls over to address $0000 allowing the read
cycle to be continued indefinitely. The read operation
is terminated by taking CS high. Refer to the Read
EEPROM Array Sequence (Figure 1).
To read the Status Register, the CS line is first pulled
low to select the device followed by the 8-bit RDSR
instruction. After the RDSR opcode is sent, the contents
of the Status Register are shifted out on the SO line.
Refer to the Read Status Register Sequence (Figure 2).
Write Sequence
Prior to any attempt to write data into the device, the
“Write Enable” Latch (WEL) must first be set by issu-
ing the WREN instruction (Figure 3). CS is first taken
LOW, then the WREN instruction is clocked into the
device. After all eight bits of the instruction are trans-
mitted, CS must then be taken HIGH. If the user con-
tinues the Write Operation without taking CS HIGH
after issuing the WREN instruction, the Write Opera-
tion will be ignored.
To write data to the EEPROM memory array, the user
then issues the WRITE instruction followed by the
16-bit address and then the data to be written. Any
unused address bits are specified to be “0’s”. The
WRITE operation minimally takes 32 clocks. CS must
go low and remain low for the duration of the opera-
tion. If the address counter reaches the end of a page
and the clock continues, the counter will roll back to
the first address of the page and overwrite any data
that may have been previously written.
For the Page Write Operation (byte or page write) to
be completed, CS can only be brought HIGH after bit 0
of the last data byte to be written is clocked in. If it is
brought HIGH at any other time, the write operation
will not be completed (Figure 4).
To write to the Status Register, the WRSR instruction
is followed by the data to be written (Figure 5). Data
bits 0 and 1 must be “0”.
While the write is in progress following a Status Regis-
ter or EEPROM Sequence, the Status Register may
be read to check the WIP bit. During this time the WIP
bit will be high.
OPERATIONAL NOTES
The device powers-up in the following state:
– The device is in the low power standby state.
– A HIGH to LOW transition on CS is required to enter
an active state and receive an instruction.
– SO pin is high impedance.
– The Write Enable Latch is reset.
– The Flag Bit is reset.
– Reset Signal is active for t
PURST
.
Data Protection
The following circuitry has been included to prevent
inadvertent writes:
– A WREN instruction must be issued to set the Write
Enable Latch.
– CS must come HIGH at the proper clock count in
order to start a nonvolatile write cycle.
X5328, X5329
相关PDF资料 |
PDF描述 |
|---|---|
| X5648P-4.5A | CAP 270PF 50V CERAMIC MONO 5% |
| X5648 | Thyristor Module |
| X5648P | RTC Module With CPU Supervisor |
| X5648S14 | RTC Module With CPU Supervisor |
| X5648S14-2.7 | RTC Module With CPU Supervisor |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X533 | 制造商:CONNOR-WINFIELD 制造商全称:Connor-Winfield Corporation 功能描述:3.3V SURFACE MOUNT 5.0 x 7.5mm LVDS CLOCK OSCILLATOR |
| X533-333.00M | 制造商:CONNOR-WINFIELD 制造商全称:Connor-Winfield Corporation 功能描述:3.3V SURFACE MOUNT 5.0 x 7.5mm LVDS CLOCK OSCILLATOR |
| X540T2 914248 | 制造商:Intel 功能描述:ETHERNETCONVERGED NETWORK ADAPTER - Boxed Product (Development Kits) |
| X540T2BLK 927245 | 制造商:Intel 功能描述:TWIN POND T2 ETHERNET CONVERGED NETWORK ADAPTER - Boxed Product (Development Kits) |
| X540T2G1P5 | 制造商:Intel 功能描述:ETHERNET CONVERGED NETWORK ADAPTER X540-T2 - Bulk |
发布紧急采购，3分钟左右您将得到回复。