- 您现在的位置：买卖IC网 > PDF目录13073 > X5643S14 (Intersil)IC CPU SUPRV 64K EE RST LO SO14 PDF资料下载
参数资料
| 型号： | X5643S14 |
| 厂商： | Intersil |
| 文件页数： | 3/19页 |
| 文件大小： | 0K |
| 描述： | IC CPU SUPRV 64K EE RST LO SO14 |
| 标准包装： | 100 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 4.38V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOICN |
| 包装： | 管件 |
X5643, X5645
PRINCIPLES OF OPERATION
Power-on Reset
Application of power to the X5643/X5645 activates a
power-on reset circuit. This circuit goes active at about
1V and pulls the RESET/RESET pin active. This signal
prevents the system microprocessor from starting to
operate with insufficient voltage or prior to stabilization
of the oscillator. When V CC exceeds the device V TRIP
value for 200ms (nominal) the circuit releases
RESET/RESET, allowing the processor to begin execut-
ing code.
To set the new V TRIP voltage, apply the desired V TRIP
threshold to the Vcc pin and tie the CS/WDI pin and
the WP pin HIGH. RESET/RESET and SO pins are
left unconnected. Then apply the programming voltage
V P to both SCK and SI and pulse CS/WDI LOW then
HIGH. Remove V P and the sequence is complete.
Figure 1. Set V TRIP Voltage
CS
V P
SCK
Low Voltage Monitoring
During operation, the X5643/X5645 monitors the V CC
level and asserts RESET/RESET if supply voltage falls
below a preset minimum V TRIP . The RESET/RESET
signal prevents the microprocessor from operating in a
power fail or brownout condition. The RESET/RESET
signal remains active until the voltage drops below 1V.
It also remains active until V CC returns and exceeds
V TRIP for 200ms.
Watchdog Timer
The watchdog timer circuit monitors the microprocessor
activity by monitoring the WDI input. The microproces-
sor must toggle the CS/WDI pin periodically to prevent a
RESET/RESET signal. The CS/WDI pin must be toggled
from HIGH to LOW prior to the expiration of the watch-
dog time out period. The state of two nonvolatile con-
trol bits in the status register determine the watchdog
timer period. The microprocessor can change these
watchdog bits, or they may be “locked” by tying the WP
pin LOW and setting the WPEN bit HIGH.
V CC Threshold Reset Procedure
V P
SI
Resetting the V TRIP Voltage
This procedure sets the V TRIP to a “native” voltage
level. For example, if the current V TRIP is 4.4V and the
V TRIP is reset, the new V TRIP is something less than
1.7V. This procedure must be used to set the voltage
to a lower value.
To reset the V TRIP voltage, apply a voltage between 2.7
and 5.5V to the V CC pin. Tie the CS/WDI pin, the WP pin,
and the SCK pin HIGH. RESET/RESET and SO pins are
left unconnected. Then apply the programming voltage
V P to the SI pin ONLY and pulse CS/WDI LOW then
HIGH. Remove V P and the sequence is complete.
Figure 2. Reset V TRIP Voltage
CS
The X5643/X5645 has a standard V CC threshold
(V TRIP ) voltage. This value will not change over normal
operating and storage conditions. However, in applica-
tions where the standard V TRIP is not exactly right, or
SCK
V CC
V P
for higher precision in the V TRIP
value, the
SI
X5643/X5645 threshold may be adjusted.
Setting the V TRIP Voltage
This procedure sets the V TRIP to a higher voltage
value. For example, if the current V TRIP is 4.4V and the
new V TRIP is 4.6V, this procedure directly makes the
change. If the new setting is lower than the current set-
ting, then it is necessary to reset the trip point before
setting the new value.
3
FN8135.1
July 18, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| 450QXW68MEFC12.5X40 | CAP ALUM 68UF 450V 20% RADIAL |
| RCC36DRAI | CONN EDGECARD 72POS R/A .100 SLD |
| EMM18DSAH | CONN EDGECARD 36POS R/A .156 SLD |
| X5643P | IC CPU SUPRV 64K EE RST LO 8DIP |
| MIC5209YU | IC REG LDO ADJ .5A TO263-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X5643S14-1.8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:SPI Serial EEPROM with Supervisory Features |
| X5643S14-2.7 | 功能描述:IC CPU SUPRV 64K EE RST LO SO14 RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:标准传输延迟为 60 µs 电压 - 阀值:3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 其它名称:LM8364BALMF30DKR |
| X5643S14-2.7A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CPU Supervisor with 64Kbit SPI EEPROM |
| X5643S14-4.5A | 制造商:XICOR 制造商全称:Xicor Inc. 功能描述:CPU Supervisor with 64Kbit SPI EEPROM |
| X5643S14I | 功能描述:IC CPU SUPRV 64K EE RST LO SO14 RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:标准传输延迟为 60 µs 电压 - 阀值:3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 其它名称:LM8364BALMF30DKR |
发布紧急采购，3分钟左右您将得到回复。