参数资料
| 型号： | X9314WSIZT1 |
| 厂商： | Intersil |
| 文件页数： | 3/9页 |
| 文件大小： | 0K |
| 描述： | IC XDCP SGL 32-TAP 10K 8-SOIC |
| 标准包装： | 2,500 |
| 系列： | XDCP™ |
| 接片： | 32 |
| 电阻（欧姆）： | 10k |
| 电路数： | 1 |
| 温度系数： | 标准值 ±600 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 3 线串行（芯片选择，递增，增/减） |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
3
FN8178.2
September 5, 2006
Typical Attenuation Characteristics (dB)
Principles of Operation
There are three sections of the X9314: the input control,
counter and decode section; the nonvolatile memory; and the
resistor array. The input control section operates just like an
up/down counter. The output of this counter is decoded to turn
on a single electronic switch connecting a point on the resistor
array to the wiper output. Under the proper conditions the
contents of the counter can be stored in nonvolatile memory
and retained for future use. The resistor array is comprised of
31 individual resistors connected in series. At either end of the
array and between each resistor is an electronic switch that
transfers the potential at that point to the wiper.
The INC, U/D and CS inputs control the movement of the
wiper along the resistor array. With CS set LOW the X9314
is selected and enabled to respond to the
U/D and INC inputs. HIGH to LOW transitions on INC will
increment or decrement (depending on the state of the U/D
input) a five bit counter. The output of this counter is
decoded to select one of thirty-two wiper positions along the
resistive array.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the last
position. That is, the counter does not wrap around when
clocked to either extreme.
The value of the counter is stored in nonvolatile memory
whenever CS transistions HIGH while the INC input is also
HIGH.
When the X9314 is powered-down, the last counter position
stored will be maintained in the nonvolatile memory. When
power is restored, the contents of the memory are recalled
and the counter is reset to the value last stored.
Operation Notes
The system may select the X9314, move the wiper and
deselect the device without having to store the latest wiper
position in nonvolatile memory. The wiper
movement is performed as described above; once the new
position is reached, the system would keep the INC LOW
while taking CS HIGH. The new wiper position would be
maintained until changed by the system or until a power-
up/down cycle recalled the previously stored data.
This would allow the system to always power-up to a preset
value stored in nonvolatile memory; then during system
operation minor adjustments could be made. The
adjustments might be based on user preference, system
parameter changes due to temperature drift, etc.
The state of U/D may be changed while CS remains LOW.
This allows the host system to enable the X9314 and then
move the wiper up and down until the proper trim is attained.
tIW/RTOTAL
The electronic switches on the X9314 operate in a “make
before break” mode when the wiper changes tap positions. If
the wiper is moved several positions multiple taps are
connected to the wiper for tIW (INC to VW change). The
RTOTAL value for the device can temporarily be reduced by
a significant amount if the wiper is moved several positions.
Power-up and Down Requirement
The are no restrictions on the sequencing of VCC and the
voltages applied to the potentiometer pins during power-up
or power-down conditions. During power-up, the data sheet
parameters for the DCP do not fully apply until 1 millisecond
after VCC reaches its final value. The VCC ramp rate spec is
always in effect.
Tap Position
0
4
8
12
16
20
24
28
31
-20
-40
-43.5
0
-60
Att
enu
atio
n
(d
B)
X9314
相关PDF资料 |
PDF描述 |
|---|---|
| DS1005S-75+ | IC DELAY LINE 5TAP 75NS 16-SOIC |
| VI-24J-MW | CONVERTER MOD DC/DC 36V 100W |
| X9511WSIZT1 | IC XDCP SGL 32TAP 10K 8-SOIC |
| DS1005S-60+T&R | IC DELAY LINE 5TAP 60NS 16-SOIC |
| VI-244-MX-B1 | CONVERTER MOD DC/DC 48V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X9314WSM | 制造商:XICOR 制造商全称:Xicor Inc. 功能描述:E2POT⑩ Nonvolatile Digital Potentiometer |
| X9314WSM3 | 制造商:XICOR 制造商全称:Xicor Inc. 功能描述:E2POT⑩ Nonvolatile Digital Potentiometer |
| X9314WST1 | 功能描述:IC XDCP SGL 32-TAP 10K 8-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:32 电阻（欧姆）:50k 电路数:1 温度系数:标准值 50 ppm/°C 存储器类型:易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 供应商设备封装:TSOT-23-6 包装:带卷 (TR) |
| X9314WST2 | 功能描述:IC XDCP SGL 32-TAP 10K 8-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:32 电阻（欧姆）:50k 电路数:1 温度系数:标准值 50 ppm/°C 存储器类型:易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 供应商设备封装:TSOT-23-6 包装:带卷 (TR) |
| X9314WSZ | 功能描述:IC XDCP SGL 32-TAP 10K 8-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻（欧姆）:100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行（芯片选择，递增，增/减） 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。