参数资料
型号: X9420YV14Z
厂商: Intersil
文件页数: 4/19页
文件大小: 0K
描述: IC DGTL POT 2.5K 1CH 14TSSOP
标准包装: 95
系列: XDCP™
接片: 64
电阻(欧姆): 2.5k
电路数: 1
温度系数: 标准值 ±300 ppm/°C
存储器类型: 非易失
接口: SPI 串行
电源电压: 4.5 V ~ 5.5 V
工作温度: 0°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 14-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 14-TSSOP
包装: 管件
12
FN8195.1
April 26, 2006
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
ENDURANCE AND DATA RETENTION
CAPACITANCE
POWER-UP TIMING
POWER-UP REQUIREMENTS (Power-up sequencing can affect correct recall of the wiper registers)
The preferred power-on sequence is as follows: First VCC, then V+ and V-, and then the potentiometer pins, RH, RL,
and RW. Voltage should not be applied to the potentiometer pins before V+ or V- is applied. The VCC ramp rate
specification should be met, and any glitches or slope changes in the VCC line should be held to <100mV if possible.
If VCC powers down, it should be held below 0.1V for more than 1 second before powering up again in order for
proper wiper register recall. Also, VCC should not reverse polarity by more than 0.5V. Recall of wiper position will not
be complete until VCC, V+ and V- reach their final value.
Notes: (5) This parameter is periodically sampled and not 100% tested.
(6) tPUR and tPUW are the delays required from the time the third (last) power supply (VCC, V+ or V-) is stable until the specific instruction
can be issued. These parameters are periodically sampled and not 100% tested.
Symbol
Parameter
Limits
Test Conditions
Min.
Typ.
Max.
Units
ICC1
VCC Supply Current (Active)
400
A
fSCK = 2MHz, SO = Open,
Other Inputs = VSS
ICC2
VCC Supply Current
(Non-volatile Write)
1mA
fSCK = 2MHz, SO = Open,
Other Inputs = VSS
ISB
VCC Current (Standby)
1
μA
SCK = SI = VSS, Addr. = VSS
ILI
Input Leakage Current
10
μAVIN = VSS to VCC
ILO
Output Leakage Current
10
μAVOUT = VSS to VCC
VIH
Input HIGH Voltage
VCC x 0.7
VCC + 0.5
V
VIL
Input LOW Voltage
-0.5
VCC x 0.1
V
VOL
Output LOW Voltage
0.4
V
IOL = 3mA
Parameter
Min.
Units
Minimum Endurance
100,000
Data Changes per Bit per Register
Data Retention
100
Years
Symbol
Test
Max.
Units
Test Conditions
COUT(5)
Output Capacitance (SO)
8
pF
VOUT = 0V
CIN(5)
Input Capacitance (A0, SI, and SCK)
6
pF
VIN = 0V
Symbol
Parameter
Max.
Units
tPUR(6)
Power-up to Initiation of Read Operation
1
ms
tPUW(6)
Power-up to Initiation of Write Operation
5
ms
tRVCC
VCC Power-up Ramp
0.2
50
V/msec
X9420
相关PDF资料
PDF描述
VE-27T-MX-B1 CONVERTER MOD DC/DC 6.5V 75W
M83723/71W2461N CONN RCPT 61POS WALL MT W/SCKT
VE-27T-MW CONVERTER MOD DC/DC 6.5V 100W
VE-JV3-MZ-S CONVERTER MOD DC/DC 24V 25W
CS2000CP-CZZ IC SYNTHESIZER & CLK MULT 10MSOP
相关代理商/技术参数
参数描述
X9420YV14Z-2.7 功能描述:IC DGTL POT 2.5K 1CH 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻(欧姆):100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行(芯片选择,递增,增/减) 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP(0.173",4.40mm 宽) 供应商设备封装:14-TSSOP 包装:带卷 (TR)
X9420YV14Z-2.7T1 功能描述:IC DGTL POT 2.5K 1CH 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻(欧姆):100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行(芯片选择,递增,增/减) 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP(0.173",4.40mm 宽) 供应商设备封装:14-TSSOP 包装:带卷 (TR)
X9420YV14ZT1 功能描述:IC DGTL POT 2.5K 1CH 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻(欧姆):100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行(芯片选择,递增,增/减) 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP(0.173",4.40mm 宽) 供应商设备封装:14-TSSOP 包装:带卷 (TR)
X9420YV-2.7 制造商:XICOR 制造商全称:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer
X9420YVI 制造商:XICOR 制造商全称:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer