- 您现在的位置：买卖IC网 > PDF目录376449 > X98014L128-3.3-Z (INTERSIL CORP) 140MHz Triple Video Digitizer with Digital PLL PDF资料下载
参数资料
| 型号： | X98014L128-3.3-Z |
| 厂商： | INTERSIL CORP |
| 元件分类： | 消费家电 |
| 英文描述： | 140MHz Triple Video Digitizer with Digital PLL |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP128 |
| 封装： | 14 X 20 MM, ROHS COMPLIANT, MS-022, MQFP-128 |
| 文件页数： | 9/29页 |
| 文件大小： | 294K |
| 代理商： | X98014L128-3.3-Z |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
9
FN8217.0
June 3, 2005
Pin Descriptions
SYMBOL
PIN
DESCRIPTION
R
IN
1
7
Analog input. Red channel 1. DC couple or AC couple through 0.1μF.
G
IN
1
12
Analog input. Green channel 1. DC couple or AC couple through 0.1μF.
B
IN
1
19
Analog input. Blue channel 1. DC couple or AC couple through 0.1μF.
RGB
GND
1
13
Analog input. Ground reference for the R, G, and B inputs of channel 1 in the DC coupled configuration.
Connect to the same ground as channel 1's R, G, and B termination resistors. This signal is not used in the
AC-coupled configuration, but the pin should still be tied to GND
A
.
SOG
IN
1
14
Analog input. Sync on Green. Connect to G
IN
1 through a 0.01μF capacitor in series with a 500
Ω
resistor.
HSYNC
IN
1
33
Digital input, 5V tolerant, 240mV hysteresis, 1.2k
Ω
impedance to GND
A
. Connect to channel 1's HSYNC
signal through a 680
Ω
series resistor.
VSYNC
IN
1
44
Digital input, 5V tolerant, 500mV hysteresis. Connect to channel 1's VSYNC signal.
R
IN
2
22
Analog input. Red channel 2. DC couple or AC couple through 0.1μF.
G
IN
2
24
Analog input. Green channel 2. DC couple or AC couple through 0.1μF.
B
IN
2
28
Analog input. Blue channel 2. DC couple or AC couple through 0.1μF.
RGB
GND
2
25
Analog input. Ground reference for the R, G, and B inputs of channel 2 in the DC coupled configuration.
Connect to the same ground as channel 1's R, G, and B termination resistors. This signal is not used in the
AC-coupled configuration, but the pin should still be tied to GND
A
.
SOG
IN
2
26
Analog input. Sync on Green. Connect to G
IN
1 through a 0.01μF capacitor in series with a 500
Ω
resistor.
HSYNC
IN
2
34
Digital input, 5V tolerant, 240mV hysteresis, 1.2k
Ω
impedance to GND
A
. Connect to channel 2's HSYNC
signal through a 680
Ω
series resistor.
VSYNC
IN
2
45
Digital input, 5V tolerant, 500mV hysteresis. Connect to channel 2's VSYNC signal.
CLOCKINV
IN
41
Digital input, 5V tolerant. When high, changes the pixel sampling phase by 180 degrees. Toggle at frame
rate during VSYNC to allow 2x undersampling to sample odd and even pixels on sequential frames. Tie to
D
GND
if unused.
RESET
46
Digital input, 5V tolerant, active low, 70k
Ω
pull-up to V
D
. Take low for at least 1μs and then high again to
reset the X98014. This pin is not necessary for normal use and may be tied directly to the V
D
supply.
XTAL
IN
39
Analog input. Connect to external 23MHz to 27MHz crystal and load capacitor (see crystal spec for
recommended loading). Typical oscillation amplitude is 1.0V
P-P
centered around 0.5V.
XTAL
OUT
40
Analog output. Connect to external 23MHz to 27MHz crystal and load capacitor (see crystal spec for
recommended loading). Typical oscillation amplitude is 1.0V
P-P
centered around 0.5V.
XTALCLK
OUT
47
3.3V digital output. Buffered crystal clock output at f
XTAL
or f
XTAL
/2. May be used as system clock for other
system components.
SADDR
48
Digital input, 5V tolerant. Address = 0x4C (0x98 including R/W bit) when tied low. Address = 0x4D (0x9A
including R/W bit) when tied high.
SCL
50
Digital input, 5V tolerant, 500mV hysteresis. Serial data clock for 2-wire interface.
SDA
49
Bidirectional Digital I/O, open drain, 5V tolerant. Serial data I/O for 2-wire interface.
R
P
[7:0]
112-119
3.3V digital output. Red channel, primary pixel data. 58K pulldown when three-stated.
R
S
[7:0]
100-107
3.3V digital output. Red channel, secondary pixel data. 58K pulldown when three-stated.
G
P
[7:0]
90-97
3.3V digital output. Green channel, primary pixel data. 58K pulldown when three-stated.
G
S
[7:0]
80-87
3.3V digital output. Green channel, secondary pixel data. 58K pulldown when three-stated.
B
P
[7:0]
68-75
3.3V digital output. Blue channel, primary pixel data. 58K pulldown when three-stated.
B
S
[7:0]
55-62
3.3V digital output. Blue channel, secondary pixel data. 58K pulldown when three-stated.
DATACLK
121
3.3V digital output. Data clock output. Equal to pixel clock rate in 24 bit mode, one half pixel clock rate in 48
bit mode.
DATACLK
122
3.3V digital output. Inverse of DATACLK.
X98014
相关PDF资料 |
PDF描述 |
|---|---|
| X98014L128-3.3 | 140MHz Triple Video Digitizer with Digital PLL |
| X98014 | 140MHz Triple Video Digitizer with Digital DLL(带有数字PLL的140MHz三路视频信号数字转换器) |
| X98017 | 170MHz Triple Video Digitizer with Digital PLL |
| X98017L128-3.3 | GIGATRUE 550 CAT PATCH CABLE NO BOOT 20FT BLACK |
| X98017L128-3.3-Z | GIGATRUE 550 CAT PATCH CBL NO BOOT 20FT BK 25 PK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X98017 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:170MHz Triple Video Digitizer with Digital PLL |
| X98017_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:170MHz Triple Video Digitizer with Digital PLL |
| X98017L128-3.3 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| X98017L128-3.3-Z | 功能描述:IC VIDEO DIGITIZER TRPL 128MQFP RoHS:是 类别:集成电路 (IC) >> 线性 - 视频处理 系列:- 标准包装:250 系列:- 类型:电平移位器 应用:LCD 电视机/监控器 安装类型:表面贴装 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-WQFN（4x4）裸露焊盘 包装:带卷 (TR) 其它名称:296-32523-2TPS65198RUYT-ND |
| X98021 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:210MHz Triple Video Digitizer with Digital PLL |
发布紧急采购，3分钟左右您将得到回复。