参数资料
型号: XA1C
元件分类: 功率/信号继电器
英文描述: POWER/SIGNAL RELAY, DPDT, MOMENTARY, 0.3A (COIL), 6VDC (COIL), 1800mW (COIL), 5A (CONTACT), 28VDC (CONTACT), SOCKET MOUNT
文件页数: 3/16页
文件大小: 1015K
代理商: XA1C
The bifilar coil
The principle is to wind on the magnetic circuit of the main coil a second coil shorted on itself. By a proper adaptation of the
internal resistance of this second coil it is possible to find an acceptable equilibrium between surge voltage and reduction of
the opening speed. To be efficient at fast voltage changes, the coupling of two coils must be perfect. This implies embedded
windings. The volume occupied by the second coil reduces the efficiency of the main coil and results in higher coil power
consumption. This method cannot be applied efficiently to products not specifically designed for this purpose.
The resistor (parallel with the coil)
For efficient action, the resistor must be of the same order of magnitude as the coil resistance. A resistor 1.5 times the coil
resistance will limit the surge to 1.5 times the supply voltage. Release time and opening speed are moderately affected. The
major problem is the extra power dissipated.
Semi-conductor devices
The diode
It is the most simple method to totally suppress the surge voltage. It has the major disadvantage of the higher reduction of
contact opening speed. This is due to the total recycling, through the diode, of the energy contained in the coil itself. The
following measurement is performed once again on the same relay. Operation times are given by the upper curve:
- time to start the movement 14ms
- transfer time 5ms
These times are multiplied by a coefficient from 4 to 8.
The lower curve shows the coil current. The increase prior to NO contact opening indicates that the contact spring dissipates
its energy. At the opening time the current becomes constant as a result of practically zero opening speed.
Due to this kind of behavior, this type of suppression must be avoided for power relays. For small relays which have to switch
low currents of less than 0.2 A, degradation of life is not that significant and the method may be acceptable.
Date of issue: 6/00
- 10 -
Page 3 of 4
相关PDF资料
PDF描述
XA1B POWER/SIGNAL RELAY, DPDT, MOMENTARY, 0.096A (COIL), 12VDC (COIL), 1152mW (COIL), 5A (CONTACT), 28VDC (CONTACT), SOCKET MOUNT
XA1A POWER/SIGNAL RELAY, DPDT, MOMENTARY, 0.056A (COIL), 28VDC (COIL), 1568mW (COIL), 5A (CONTACT), 28VDC (CONTACT), SOCKET MOUNT
XC4010E-1PGG191M FPGA, 400 CLBS, 7000 GATES, 166 MHz, CPGA191
XC4010E-2PGG191M FPGA, 400 CLBS, 7000 GATES, 125 MHz, CPGA191
XC4010E-3PGG191M FPGA, 400 CLBS, 7000 GATES, 125 MHz, CPGA191
相关代理商/技术参数
参数描述
X-A1C 制造商:Leach International Corporation 功能描述:MID RANGE - Bulk
X-A1C-300M 制造商:Leach International Corporation 功能描述:MID RANGE - Bulk
XA1E-BV301-R 制造商:IDEC Corporation 功能描述:SWITCH;16MM XA ESTOP 29MM MSHRM ,RED 制造商:IDEC Corporation 功能描述:SWITCH, EMERGENCY STOP, 1NC, 250VAC; Contact Configuration:SPST-NC; Switch Operation:Pushlock Turn Reset; Contact Voltage DC Nom:250V; Contact Voltage AC Nom:250V; Contact Current Max:3A; Actuator Style:Mushroom; IP Rating:IP65 ;RoHS Compliant: Yes 制造商:IDEC CORPORATION 功能描述:16mm XA Estop 29mm Mshrm Sldr
XA1E-BV301-RH 制造商:IDEC CORPORATION 功能描述:XA 16mm Estop Psh/Trn-Psh/Pll
XA1E-BV302-R 制造商:IDEC Corporation 功能描述:SWITCH,29MM,MUSHROOM,SOLDER TERMINAL,2NC 制造商:IDEC Corporation 功能描述:Emergency Stop Pushbutton Switch 制造商:IDEC Corporation 功能描述:SWITCH, EMERGENCY STOP, 2NC, 250VAC; Contact Configuration:DPST-NC; Switch Operation:Pushlock Reset/Push-Pull; Contact Voltage DC Nom:250V; Contact Voltage AC Nom:250V; Contact Current Max:3A; Actuator Style:Mushroom; IP Rating:IP65 ;RoHS Compliant: Yes 制造商:IDEC Corporation 功能描述:Electromechanical Switch Emergency Stop Switch N.C. 制造商:IDEC CORPORATION 功能描述:Electromechanical Switch Emergency Stop Switch N.C.