参数资料
| 型号： | XC2S30-6TQ144C |
| 厂商： | Xilinx Inc |
| 文件页数： | 78/99页 |
| 文件大小： | 0K |
| 描述： | IC FPGA 2.5V C-TEMP 144-TQFP |
| 标准包装： | 60 |
| 系列： | Spartan®-II |
| LAB/CLB数： | 216 |
| 逻辑元件/单元数： | 972 |
| RAM 位总计： | 24576 |
| 输入/输出数： | 92 |
| 门数： | 30000 |
| 电源电压： | 2.375 V ~ 2.625 V |
| 安装类型： | 表面贴装 |
| 工作温度： | 0°C ~ 85°C |
| 封装/外壳： | 144-LQFP |
| 供应商设备封装： | 144-TQFP（20x20） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页当前第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页
Spartan-II FPGA Family: Functional Description
DS001-2 (v2.8) June 13, 2008
Module 2 of 4
Product Specification
8
R
The three IOB registers function either as edge-triggered
D-type flip-flops or as level-sensitive latches. Each IOB has
a clock signal (CLK) shared by the three registers and
independent Clock Enable (CE) signals for each register. In
addition to the CLK and CE control signals, the three
registers share a Set/Reset (SR). For each register, this
signal can be independently configured as a synchronous
Set, a synchronous Reset, an asynchronous Preset, or an
asynchronous Clear.
A feature not shown in the block diagram, but controlled by
the software, is polarity control. The input and output buffers
and all of the IOB control signals have independent polarity
controls.
Optional pull-up and pull-down resistors and an optional
weak-keeper circuit are attached to each pad. Prior to
configuration all outputs not involved in configuration are
forced into their high-impedance state. The pull-down
resistors and the weak-keeper circuits are inactive, but
inputs may optionally be pulled up.
The activation of pull-up resistors prior to configuration is
controlled on a global basis by the configuration mode pins.
If the pull-up resistors are not activated, all the pins will float.
Consequently, external pull-up or pull-down resistors must
be provided on pins required to be at a well-defined logic
level prior to configuration.
All pads are protected against damage from electrostatic
discharge (ESD) and from over-voltage transients. Two
forms of over-voltage protection are provided, one that
permits 5V compliance, and one that does not. For 5V
compliance, a zener-like structure connected to ground
turns on when the output rises to approximately 6.5V. When
5V compliance is not required, a conventional clamp diode
may be connected to the output supply voltage, VCCO. The
type of over-voltage protection can be selected
independently for each pad.
All Spartan-II FPGA IOBs support IEEE 1149.1-compatible
boundary scan testing.
Input Path
A buffer In the Spartan-II FPGA IOB input path routes the
input signal either directly to internal logic or through an
optional input flip-flop.
An optional delay element at the D-input of this flip-flop
eliminates pad-to-pad hold time. The delay is matched to
the internal clock-distribution delay of the FPGA, and when
used, assures that the pad-to-pad hold time is zero.
Each input buffer can be configured to conform to any of the
low-voltage signaling standards supported. In some of
these standards the input buffer utilizes a user-supplied
threshold voltage, VREF. The need to supply VREF imposes
constraints on which standards can used in close proximity
to each other. See "I/O Banking," page 9.
There are optional pull-up and pull-down resistors at each
input for use after configuration.
Output Path
The output path includes a 3-state output buffer that drives
the output signal onto the pad. The output signal can be
routed to the buffer directly from the internal logic or through
an optional IOB output flip-flop.
The 3-state control of the output can also be routed directly
from the internal logic or through a flip-flip that provides
synchronous enable and disable.
Each output driver can be individually programmed for a
wide range of low-voltage signaling standards. Each output
buffer can source up to 24 mA and sink up to 48 mA. Drive
strength and slew rate controls minimize bus transients.
In most signaling standards, the output high voltage
depends on an externally supplied VCCO voltage. The need
to supply VCCO imposes constraints on which standards
can be used in close proximity to each other. See "I/O
An optional weak-keeper circuit is connected to each
output. When selected, the circuit monitors the voltage on
the pad and weakly drives the pin High or Low to match the
input signal. If the pin is connected to a multiple-source
signal, the weak keeper holds the signal in its last state if all
Table 3: Standards Supported by I/O (Typical Values)
I/O Standard
Input
Reference
Voltage
(VREF)
Output
Source
Voltage
(VCCO)
Board
Termination
Voltage
(VTT)
LVTTL (2-24 mA)
N/A
3.3
N/A
LVCMOS2
N/A
2.5
N/A
PCI (3V/5V,
33 MHz/66 MHz)
N/A
3.3
N/A
GTL
0.8
N/A
1.2
GTL+
1.0
N/A
1.5
HSTL Class I
0.75
1.5
0.75
HSTL Class III
0.9
1.5
HSTL Class IV
0.9
1.5
SSTL3 Class I
and II
1.5
3.3
1.5
SSTL2 Class I
and II
1.25
2.5
1.25
CTT
1.5
3.3
1.5
AGP-2X
1.32
3.3
N/A
相关PDF资料 |
PDF描述 |
|---|---|
| 24LC024HT-E/MS | IC EEPROM 2KBIT 400KHZ 8MSOP |
| 748610-2 | CONT, HD22 CS SCKT, 30AU |
| 24LC014T-E/MS | IC EEPROM 1KBIT 400KHZ 8MSOP |
| XC2S30-5TQ144I | IC FPGA 2.5V I-TEMP 144-TQFP |
| XC6SLX4-L1CPG196C | IC FPGA SPARTAN 6 3K 196CPGBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XC2S30-6TQ144I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-II 2.5V FPGA Family:Introduction and Ordering Information |
| XC2S30-6TQG144C | 制造商:Xilinx 功能描述:FPGA SPARTAN-II 30K GATES 972 CELLS 263MHZ 2.5V 144TQFP EP - Trays 制造商:Xilinx 功能描述:IC SYSTEM GATE |
| XC2S30-6TQG144I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-II FPGA Family |
| XC2S30-6VQ100C | 功能描述:IC FPGA 2.5V C-TEMP 100-PQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:Spartan®-II 标准包装:40 系列:Spartan® 6 LX LAB/CLB数:3411 逻辑元件/单元数:43661 RAM 位总计:2138112 输入/输出数:358 门数:- 电源电压:1.14 V ~ 1.26 V 安装类型:表面贴装 工作温度:-40°C ~ 100°C 封装/外壳:676-BGA 供应商设备封装:676-FBGA（27x27） |
| XC2S30-6VQ100I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-II 2.5V FPGA Family:Introduction and Ordering Information |
发布紧急采购，3分钟左右您将得到回复。